Sealey AK2946 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly
maintained, give years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
! WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using the torch.
Familiarise yourself with the application and limitations, as well as the potential hazards, peculiar to the torch.
"
Butane gas is highly flammable, so keep an appropriate fire extinguisher close to hand.
"
! WARNING! Use and handle the butane gas (lighter fuel) in accordance with the instructions supplied with the fuel.
Keep the work area clean, uncluttered and ensure there is adequate ventilation and lighting.
"
Keep children and unauthorised persons away from the working area.
"
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain and/or tie back long hair.
"
Point the torch away from yourself and others when igniting flame.
"
Keep hands and body clear of the torch head when operating as it becomes very hot.
"
Secure unstable workpiece with a clamp, vice or other adequate holding device.
"
DO NOT get the torch wet.
#
DO NOT use torch where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning rags etc.
#
DO NOT use the torch for any purpose other than for which it is designed.
#
DO NOT use accessories other than those supplied with the torch.
#
! WARNING! DO NOT touch the torch head during, or immediately after, use. Allow the torch to cool naturally before handling it or returning it
to its storage case.
DO NOT cool the torch in water.
#
DO NOT point the torch at yourself, others, or animals.
#
DO NOT operate the torch when you are tired, or under the influence of alcohol, drugs or intoxicating medication.
#
DO NOT allow untrained persons to operate the torch.
#
DO NOT operate the torch if any parts are damaged or missing as this may cause failure and/or personal injury.
#
DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool.
#
DO NOT leave the torch, after use, until it has cooled.
#
When work is complete, allow the torch to cool. Clean the torch and accessories, return to case and store in a safe, dry childproof location.
"
DO NOT store in direct sunlight or where the temperature could exceed 104
#
! WARNING! Failure to use the torch correctly may result in fire, damage and/or personal injury.
$ DANGER! The flame is invisible in sunlight - be extremely cautious.
2. INTRODUCTION
Portable and lightweight torch with piezoelectric start. Features adjustable heating control ranging up to 450°C (approximately). Removable
solder tip transforms torch into burning flame heat source. Supplied with a variety of nozzles for various applications including a flameless heat
source adaptor. Safety cap for storage. Sponge cleaning tray and small roll of solder wire. Suitable for heating, soldering and shrinking.
Powered by Butane (lighter fluid).
AK2946 Kit comprises: Butane Solder Torch, Soldering Head with 3 Solder Tips, Spanner for solder tips, Curved deflector plate, Hot Knife, Sponge,
Safety Cap.
3. OPERATING INSTRUCTIONS
WARNING! Ensure you have read and understood the safety instructions in Section 1 before using the torch.
!
Note: The torch is supplied without butane gas. Before use it must be fuelled as follows:
3.1. TO FUEL THE TORCH
3.1.1. Use only high quality butane gas (lighter fuel) to fill the torch.
3.1.2. Ensure the 'On/Off' switch is in the 'Off' position. See fig.3, 'Gas On/Off Switch'.
3.1.3. Follow the instructions on the butane
fuel can.
3.1.4. Apply the can filler tip to the torch
base filler valve (fig.1). Use a
pumping action for best filling results.
3.1.5. Once full, allow gas in the torch to
stand and stabilise for a few minutes
before use.
fig. 1
BUTANE SOLDERING/HEATING TORCH KIT
F/40 C
O O
fig. 2
INSTRUCTIONS FOR:
AK2946
MODEL:
AK2946 - 1 - 18/06/07