Toyota Corolla 2004 Manual page 117

03–38
3rd gear radial clearance
Input shaft run out
Input shaft outer diameter
4th gear inside diameter
3rd gear inside diameter
3rd gear synchronizer ring back and 3rd gear spline end clearance
4th gear synchronizer ring back and 3rd gear spline end clearance
Gear shift fork No.2 claw and glove of the transmission hub sleeve No.2
clearance
Transmission clutch hub No.2 snap ring thickness
Input shaft rear radial ball bearing snap ring
OUTPUT SHAFT ASSY
1st gear thrust clearance
2nd gear thrust clearance
1st gear radial clearance
1st gear radial clearance
Output shaft maximum run out
Output shaft outer diameter
2nd gear inside diameter
1st gear inside diameter
1st gear thrust washer thickness
Synchronizer ring set No.2 back and 2nd gear spline end clearance
Synchronizer ring set No.1 back and 2nd gear spline end clearance
Reverse gear groove and reverse gear shift fork claw clearance
2004 COROLLA (RM1037U)
SERVICE SPECIFICATIONS
KOYO made STD:
NSK made STD:
Mark: 0
KOYO made:
NSK made:
KOYO made:
NSK made:
– MANUAL TRANSMISSION / TRANSAXLE
0.015 – 0.058 mm (0.0006 – 0.0023 in.)
MAX: 0.058 mm (0.0023 in.)
0.015 – 0.056 mm (0.0006 – 0.0022 in.)
MAX: 0.056 mm (0.0022 in.)
MAX: 0.015 mm (0.0006 in.)
STD: A 24.885 – 24.900 mm (0.9797 – 0.9803 in.)
B 28.985 – 29.000 mm (1.1411 – 1.1417 in.)
C 30.985 – 31.000 mm (1.2198 – 1.2204 in.)
D 24.985 – 25.000 mm (0.9836 – 0.9842 in.)
Min: A 24.885 mm (0.9797 in.)
B 28.985 mm (1.1411 in.)
C 30.985 mm (1.2198 in.)
D 24.985 mm (0.9836 in.)
STD: 34.015 – 34.031 mm (1.3391 – 1.3398 in.)
MAX: 34.031 mm (1.3398 in.)
STD: 36.015 – 36.031 mm (1.4179 – 1.4185 in.)
MAX: 36.031 mm (1.4185 in.)
Min: 0.65 mm (0.0256 in.)
Min: 0.75 mm (0.0295 in.)
0.15 – 0.35 mm (0.0059 – 0.0137 in.)
2.30 mm (0.0906 in.)
1 2.36 mm (0.0929 in.)
2 2.42 mm (0.0953 in.)
3 2.48 mm (0.0976 in.)
4 2.54 mm (0.1000 in.)
5 2.60 mm (0.1024 in.)
Mark: 0 2.29 mm (0.0901 in.)
1 2.35 mm (0.0925 in.)
2 2.41 mm (0.0948 in.)
3 2.47 mm (0.0972 in.)
4 2.53 mm (0.0996 in.)
5 2.59 mm (0.1019 in.)
STD: 0.10 – 0.40 mm (0.0039 – 0.0157 in.)
STD: 0.10 – 0.45 mm (0.0039 – 0.0177 in.)
0.015 – 0.058 mm (0.0006 – 0.0023 in.)
0.015 – 0.056 mm (0.0006 – 0.0022 in.)
0.015 – 0.058 mm (0.0006 – 0.0023 in.)
0.015 – 0.056 mm (0.0006 – 0.0022 in.)
0.015 mm (0.0006 in.)
Part: A 31.985 mm (1.2592 in.)
B 37.985 mm (1.4955 in.)
C 32.985 mm (1.2986 in.)
New: 38.015 – 38.031 mm (1.4967 – 1.4973 in.)
MAX: 38.031 mm (1.4973 in.)
New: 44.015 – 44.031 mm (1.7329 – 1.7335 in.)
MAX: 44.031 mm (1.7335 in.)
New: 5.975 – 6.025 mm (0.2352 – 0.2372 in.)
Min: 5.975 mm (0.2352 in.)
0.7 – 1.3 mm (0.0276 – 0.0512 in.)
0.75 – 1.65 mm (0.0295 – 0.065 in.)
0.15 – 0.35 mm (0.0059 – 0.0138 in.)
Author : Date :
142