Rocky's EAZY ROLLERS 305/336 Instructions

This box contains the following items:
RE-
ITEM QTY. DESCRIPTION ORDER
# #
Self-tapping Screw
1 12 501
5 2 5/16"x1" Bolt 505
11 2 3/8"x6" Anchor Bolt 511
Concrete Anchor
15 2 515
19 2 5/16" Washer 505
21 8 3/8" Washer 21
2 Spring 517
25
29 4 Acorn Nut 523
#3 A-Frame
55 2 55
61 1 White Knob 533
65 2 4" Regular Hub 539
Small Handle
71 1 545
101 10 Male Grommet 549
103 10 Female Grommet 549
2 Plastic Bushing 555
105
107 2 Plastic Washer 555
Spring Guard
109 2 109
201 1 22' Strapping 587
209 4 2" Plastic Wheels 583
Any questions,check out our Web Site:
www.rockysrollers.com
Go to FAQ (Frequently AskedQuestiona)

Tools Required:

Reversible Electric Drill
1/2" Concrete (masonary) Drill Bit
Hammer & Center Punch or Nail.
5/16" Hex Head Socket Bit
1/2" Wrench
5/8" Wrench
ROCKY'S EAZY ROLLERS INSTRUCTIONS - #3 PORTABLE
1
For use with 4" (outside diameter)
aluminum irrigation tubing.
(Not Supplied By Rocky's)
NOTE:
Tube length should be about 1' wider than pool.
Insert one end of irrigation tubing into 4" hub
(item #65).
65
With 2 self-drill/tapping screws
SELF-DRILLING
(item #1), attach hub to tube using
electric drill. Apply pressure to
ensure screw cuts into
aluminum tube then cuts
1
it's own thread.
(No predrilling required)
Repeat with other side.
4
3
For regular shaped pools,
MARK
align the outside edge of the
#1
tube parallel with the end of
Using one of the two holes in the A-frame as a guide,
the pool.
make mark #1 on deck. With a 1/2" concrete drill
For irregular shaped pools, bit, drill a 1 1/2" deep hole at mark #1. Complete
the outside edge of the tube steps 5 and 6 before continuing with step 4.
On the other side of the roller unit, make mark #2 by
should be 3'
using one of the two holes in the A-frame as of guide.
i n s i d e
With a 1/2" concrete drill bit, drill a 1 1/2" deep hole
from the
at mark #2.
end of
NOTE:
the pool.
Set one bolt at front of frame on one end and
one at the rear of the frame on the other end.
®
2
55
29
NOTE: 105
APPLY WATERPROOF
GREASE.
65
21
209
5
then tap the slug into the hole with a
MARK
hammer, then using a center punch or
#2
large nail drive the slug down into the
anchor forcing legs out into concrete.
1/16"
5
Bolt the castors (item #209) to the A-frames
19
71
(item #55), as shown in the diagram.
107
Assemble one end unit to the tube, using
the small handle (item #71), as shown in
the diagram.
Assemble the other end unit to the tube,
using the white knob (item #61).
For smoother operation, apply
petroleum based grease between the
hub (item #65) and the black bushing
61
(item #105). This should be done once a
year.
Position the assembled roller unit at the
widest end of the pool.
V E R Y I M P O R T A N T
PREVENT DROWNING
Attach Warning Label to one end of tube.
Drive the concrete anchor into
6
the hole with a hammer.
Leave the anchor raised 1/
16".
To set the concrete anchor, spring guard (item #109) and
through the hole of the A-frame.
Hit center slug
with hammer &
center punch,or
large nail.
Slug
15
Insert the anchor bolt
(item #11) through
the spring (item
#25), through the
11
25
109