Table of Contents
Advertisement
Quick Links
① Power:
② Input:
③ Menu:
④
− :
⑤
+ :
⑥ Back:
⑦ Speaker:
⑧ Test Input A:
⑨ Test Input B:
⑩ Source Input:
⑪ Charging Port:
AVA HDMI® Display Tester
BL-526-105
Button and Port Layout:
Display Tester On/Off
Changes Input modes on Display Tester
Access to the Settings Menu
Menu navigation "Down"
Menu navigation "Up"
Returns to the previous menu
Audio output (fixed)
To be used in "HDMI Test Input" mode for cable testing
To be used in "HDMI Test Input" mode for cable testing
To be used in "HDMI Display Input" mode for source testing
5VDC Micro USB Port
REV 1.0
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Steren BL-526-105
Summary of Contents for Steren BL-526-105
- Page 1 REV 1.0 AVA HDMI® Display Tester BL-526-105 Button and Port Layout: ① Power: Display Tester On/Off ② Input: Changes Input modes on Display Tester ③ Menu: Access to the Settings Menu ④ − : Menu navigation “Down” ⑤ Menu navigation “Up”...
- Page 2 Getting Started: PLEASE READ ENTIRE CONTENTS OF THE MANUAL BEFORE OPERATION Powering On/Off: 1. To power on the unit, press and hold the ① “Power” button for 3 seconds until the pop-up menu shown below appears (Fig 1). 2. To power off the unit, press and hold the ① “Power” for 3 seconds and release. (Fig 1) Changing Input Modes: 1.
- Page 3 Color Menu: The Color menu allows for manual adjustments of the display picture. It is recommended to keep the values set to the default values: (Fig 2) 1. Brightness: Adjust the display brightness Default value is 50 2. Contrast: Adjust the display contrast Default value is 50 3.
- Page 4 Function Menu: The Function menu allows for manual adjustments of other various functions. It is recommended to keep the values set to the default values: (Fig 4) 1. Reset Reset system settings to default. 2. Display Ratio: Adjust the display ratio of the display. Default value is 16:9 3.
- Page 5 HDMI Cable Testing: Below are examples of some of the different test results you may encounter when checking HDMI Cables with the Steren HDMI Display Tester. ***Please note HDMI cable testing will only function with Non-Active HDMI cables*** 1. Successful test. All 19 lines display as green which is a full passing result. (Fig 5) (Fig 5) 2.
- Page 6 4. If an HDMI cable has broken wires internally, the test display may look as shown in (Fig 8). It is recommended to use another cable for the installation. (Fig 8) 5. If the cable has a cross connect or a short circuit problem, the color of the affected lines will change to white.
- Page 7 Source Display Testing: 1. If the HDMI cable is not correctly connected to the display tester and/or to the source device there will be a pop up box on the tester display showing “No Signal”. (Fig 10) (Fig 10) 2. A successful playback test will result in picture and audio playback on the display tester. (Fig 11) (Fig 11) 3.
- Page 8 1-year warranty, to inspect the damaged Steren product, and all costs of shipping the Steren product to Steren for inspection shall be borne solely by the purchaser. In order to recover under this limited 1-year warranty, purchaser must make claim to Steren within 60 days of occurrence, and must present acceptable proof of original ownership (such as original receipt, warranty card registration, on-line registration, or other documentation Steren deems acceptable) for the product.
Need help?
Do you have a question about the BL-526-105 and is the answer not in the manual?
Questions and answers