Dyson SV10 ABSOLUTE Operating Manual page 20

WASHABLE PARTS
WASHING THE BRUSHBARS
• Your appliance has two washable brush bars, check and wash these regularly
according to the following instructions to maintain performance.
• Ensure the appliance is disconnected from the charger before removing the
brush bar. Be careful not to pull the 'ON' trigger.
TO REMOVE, WASH AND REPLACE BRUSHBARS:
• Please refer to the 'Washing the brush bars' illustrations alongside the
instructions below.
• Turn the cleaner head upside down so the underside of the cleaner head is
facing you. Use a coin to turn the fastener one quarter anti-clockwise to the
unlocked position.
• Rotate the end cap to the open position. Gently slide the large brush bar away
from the cleaner head.
• Remove the end cap from the large brush bar.
• Lift out the small brush bar from the octagonal end and pull away from the
cleaner head.
• Hold the brush bars under running water and gently rub to remove any lint or
dirt
• Stand both brush bars upright. Ensure the large brush bar is stood upright as
shown. Leave to dry completely for a minimum of 24 hours.
• Before replacing, check that the brush bars are completely dry. Refit the small
brush bar before the large one. Insert the round end of the small brush bar into
place. Push down the octagonal end until it clicks into place.
• Reattach the end cap to the brush bar.
• Slide the large brush bar back onto the cleaner head, around the motor.
The end cap should be in the open position as shown. Once in place, rotate the
end cap back into the closed position.
• Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is
fully turned and the brush bars are secure.
WASHING THE FILTERS
• Your appliance has two washable filters; wash the filters at least once a month
according to the following instructions to maintain performance. More frequent
washing may be required where the user: vacuums fine dust, operates mainly in
'Powerful suction' mode, or uses the machine intensively.
WASHING FILTER A
• Ensure the appliance is disconnected from the charger before removing the
filter. Be careful not to pull the 'ON' trigger.
• Check and wash the filter regularly according to instructions to maintain
performance.
• The filter may require more frequent washing if vacuuming fine dust or if used
mainly in 'Powerful suction' mode.
• To remove the filter, lift it out of the top of the appliance.
• Wash the filter with cold water only.
• Run water over the outside of the filter until the water runs clear.
• Squeeze and twist with both hands to make sure the excess water is removed.
• Leave the filter to dry completely for a minimum of 24 hours.
• Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
• To refit, place the dry filter back into the top of the appliance. Make sure it is
seated properly.
WASHING FILTER B
• To remove the filter, twist anti clockwise to the open position and pull away from
the appliance.
• Wash the inside of the filter under cold running water, rotating the filter to
ensure all pleats are covered.
• Gently tap the filter against the side of the sink several times to remove any
debris.
• Repeat this process 4-5 times until the filter is clean.
• Place the filter upright, with the Max button facing upwards, and leave to dry
completely for a minimum of 24 hours.
• To refit, return the filter to the open position and twist clockwise until it clicks into
place.
BLOCKAGES – AUTOMATIC CUT-OUT
• This appliance is fitted with an automatic cut-out.
• If any part becomes blocked the appliance may automatically cut out.
• This will happen after the motor pulses a number of times (i.e switches on and
off in quick succession).
• Leave to cool down before looking for blockages.
• Ensure the appliance is disconnected from the charger before looking for
blockages. Failure to do so could result in personal injury.
• Clear any blockage before restarting.
• Refit all parts securely before using.
• Clearing blockages is not covered by your guarantee.
LOOKING FOR BLOCKAGES
The motor will pulse when there is a blockage. Please follow the instructions
below to locate the blockage:
• Ensure the appliance is disconnected from the charger before looking for
blockages. Be careful not to pull the 'ON' trigger.
• Do not operate while checking for blockages. Failure to do so could result in
personal injury.
• Beware of sharp objects when checking for blockages.
• To check for blockages in the main body of the appliance, remove the clear
bin and cyclone as per the instructions in the cleaning the clear bin section and
remove the blockage. Please consult the 'Stubborn blockages' section of the
illustrations for further guidance.
• If you cannot clear an obstruction you may need to remove the brush bars,
please follow the instructions below:
– To remove the soft roller cleanerhead brush bars, please refer to the
'Washing the soft roller cleanerhead brush bars' section. Remove the
obstruction and replace the brush bars as shown in the 'Washing the soft
roller cleanerhead brush bars' section. Ensure that the fastener is fully
turned and the base plate and brush bars are secure before operating
the appliance.
– To remove the brush bars from the direct drive cleanerhead, use a coin to
unlock the fastener and slide the brush bars out of the cleanerhead.
Remove the obstruction. Replace the brush bar and secure it by tightening the
fastener. Ensure it is fixed firmly before operating the appliance.
• This product has carbon fibre brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
• Refit all parts securely before using.
• Clearing blockages is not covered by your guarantee.
CHARGING AND STORING
• This appliance will switch 'OFF' if the battery temperature is below 3°C (37.4°F).
This is designed to protect the motor and battery. Do not charge the appliance
and then move it to an area with a temperature below 3˚C (37.4°F) for storage
purposes.
• To help prolong battery life, avoid recharging immediately after a full discharge.
Allow to cool for a few minutes.
• Avoid using the appliance with the battery flush to a surface. This will help it run
cooler and prolong battery run time and life.
BATTERY SAFETY INSTRUCTIONS
• If the battery needs replacing please contact the Dyson Helpline.
• Use only Dyson chargers for charging this Dyson appliance.
• The battery is a sealed unit and under normal circumstances poses no safety
concerns. In the unlikely event that liquid leaks from the battery do not touch the
liquid and observe the following precautions:
– Skin contact – can cause irritation. Wash with soap and water.
– Inhalation – can cause respiratory irritation. Expose to fresh air and seek
medical advice.
– Eye contact – can cause irritation. Immediately flush eyes thoroughly with
water for at least 15 minutes. Seek medical attention.
– Disposal – wear gloves to handle the battery and dispose of immediately,
following local ordinances or regulations.
CAUTION
The battery used in this device may present a risk of fire or chemical burn if
mistreated. Do not disassemble, short contacts, heat above 60°C (140°F),
or incinerate. Keep away from children. Do not disassemble and do not dispose
of in fire.
DISPOSAL INFORMATION
• Dispose of or recycle the battery in accordance with local ordinances or
regulations.
• Keep the used batteries away from children as these can still harm children if
swallowed.
• Dyson products are made from high grade recyclable materials. Recycle where
possible.
• The battery should be removed from the product before disposal.
ONLINE SUPPORT
• For online help, general tips, videos and useful information about Dyson.
– www.dyson.com/SV10support
20