Advertisement
Quick Links
Federal Communications Commission Statement
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
FCC Caution
To assure continued compliance, any changes or modifications not expressly approved by the
party responsible for compliance
may void the user's authority to operate his equipment. (Example – use only shielded
interface cables when connecting to computer or peripheral devices)
FCC Statement in User's Manual (for class B) FCC Section 15.105 "Federal Communications
Commission (FCC) Statement"
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
Vision Guarantees that every wireless PIR sensor is free from physical defects in material
and workmanship under normal use for one year from the date of purchase. If the product
proves defective during this one-year warranty period, Vision will replace it free of charge.
Vision does not issue any refunds. This warranty is extended to the original end user
purchase only and is not transferable. This warranty does not apply to : (1) damage to
units caused by accident, dropping or abuse in handling, or any negligent use; (2) units
which have been subject to unauthorized repair, taken apart, or otherwise modified; (3)
units not used in accordance with instruction; (4) damages exceeding the cost of the
product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost.
For information on additional devices, please visit us at
www.visionsecurity.com.tw
ZP3113-7
V0 1090803
Installation & Operation Manual
ZP3113IN-7
ZP3113EU-7
ZP3113RU-7
ZP3113US-7
ZP3113BR-7
ZP3113IL-7
ZP3113HK-7
ZP3113TH-7
ZP3113KR-7
ZP3113JP-7
4-in-1 Motion Sensor
(Temp./Humidity/Light Sensor Built-In)
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Vision ZP3113IN-7
Summary of Contents for Vision ZP3113IN-7
- Page 1 Vision will replace it free of charge. Vision does not issue any refunds. This warranty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or abuse in handling, or any negligent use;...
-
Page 2: Product Description And Specification
Introduction Thanks for choosing the Vision’s wireless 4-in-1 Motion sensor of the home security device. The new multi-sensor consists of motion, temperature, humidity & light sensor for combing several functionality in one device; more attractive and economic consideration. This sensor is a Z-Wave... - Page 3 Configuration – Temperature Z-Wave Command Classes: COMMAND_CLASS_APPLICATION_STATUS Size VALUE Default COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3 COMMAND_CLASS_ASSOCIATION_V2 °C 0x00 °C(0x00) Parameter 1 COMMAND_CLASS_BATTERY °F 0x01 COMMAND_CLASS_CONFIGURATION_V4 1~50 (Set up from 3 (°C) Parameter 2 COMMAND_CLASS_DEVICE_RESET_LOCALLY 0.1°C~5°C) COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5 Configuration – Humidity COMMAND_CLASS_INDICATOR_V3 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 Size VALUE Default COMMAND_CLASS_NOTIFICATION_V8 1~50 (Set up from...
-
Page 4: Installation
Configuration – Acknowledge: 8. Battery Capacity Detection: * Use “Battery Get” command to have the battery capacity back in % * It will detect the battery capacity automatically Size Value * Low Battery Auto Report when power is lower than 2.4V +/- 0.1V 0 ~ 10 (unsigned decimal) Times Parameter 8 (default: 3 Times) -
Page 5: Operation
Operation Support SECURITY S0, SECURITY S2 UNAUTHENTICATED & SECURITY S2 AUTHENTICATED. Using adhesive tape to mount ZP3113 at 2 meters above surface. To enhance proper operation, place ZP3113 on the location which can detect the room widely. The PIR Support SmartStart, please scan the QR Code from ZP3113 for SmartStart. QR code needs one minute to be stable after initial power on, please proceed motion detection after and PIN is located on the device, also there is a Full DSK string on the enclosed DSK that.
Need help?
Do you have a question about the ZP3113IN-7 and is the answer not in the manual?
Questions and answers