Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FLETCHER F-60
Summary of Contents for FLETCHER F-60
- Page 1 Fletcher F-60 62" Semi- Rigid Flexible Substrate Cutter Instruction Manual...
- Page 2 OWNER’S MANUAL Fletcher F-60 Cutter The Fletcher-Terry Company 91 Clark Drive • East Berlin, CT USA 06023 Tel 860.677.7331 • Toll-Free (U.S. only) 888.888.5165 • Fax 860.828.3400 customerservice@fletcher-terry.com • www.fletcher-terry.com Form ENG - 052212...
-
Page 3: Table Of Contents
Plastic Knife Blade Cartridge………………………………………………….. 2. d. Inserting Plastic Knife Blade…………………………………………………... 3. Trimming Green Sight-Line Strip to Size………………………………………... 3. III. F-60 Cutting Head – Operating Lock and Cut Feature………………………... 4. General Maintenance Tips…………………………………………………………. 4. F-60 Cutting Head – Field Adjustment…………………………………………... 4. Troubling Shooting Guide…………………………………………………………. 5. -
Page 4: Introduction
Congratulations on purchasing a Fletcher F-60 Cutter. You have a tool that will perform consistently and made of a long-lasting durable material. The F-60 is perfect for all your cutting needs—cutting corrugated plastic, Gatorboard, foamboard up to ½” (13mm) and PVC up to 3mm. - Page 5 SAFETY FIRST! Please read through this manual before operating the Fletcher F-60. If after reviewing these pages you still have questions about using the machine, contact our Customer Service Department toll-free at 800.843.3826 in the United States. Outside the United States, call +860.828.3400 or you may email us at customerservice@fletcher-terry.com.
-
Page 6: Operation Of The F-60 Cutter
Check the exterior of the packing box to make sure there is no visible damage. After unpacking the unit, check to make sure you have all the parts and there is no damage to the machine. All components and major assemblies have already been factory installed on the F-60 Cutter. •... -
Page 7: Operating Rail Clamp Mechanism
Utilize the built-in square bar to securely hold the material straight during the cutting process. c. Plastic Knife Blade Cartridge The F-60 cutter uses a plastic knife blade cartridge for cutting a wide range of semi-rigid and flexible materials. The cutting blade is permanently molded in place and CANNOT be removed and replaced with a new blade in the plastic cartridge holder. -
Page 8: Trimming Green Sight-Line Strip To Size
5. Note: There will be a portion on either end of the Green Strip that will not be cut 6. Using a utility knife, continue the cut made by the F-60 on either end and remove the excess Green Strip material. -
Page 9: General Maintenance Tips
III. F-60 Cutting Head – “Lock and Cut” Feature The F-60 Cutter offers a unique “lock and cut” feature as part of its cutting head assembly. When the operator lowers the cutting head, it locks into the down position during the cutting process. -
Page 10: Common Consumables And Accessories
V. Troubleshooting Guide Check the guide below to troubleshoot some common issues during the use of your F-60 Cutter. If the Troubleshooting Guide or the Frequently Asked Questions section listed below does not answer your questions, please contact our Customer Service Department at 800.843.3826, or send an email to customerservice@fletcher-terry.com. - Page 11 Table Exploded View – Left Side Table Exploded View – Right Side...
-
Page 12: Parts List - Cutting Head Assembly
IX. Parts List – Cutting Head Assembly Item Part Description Item Part Description 17-841 Cutter Housing 17-849 Detent Pin 17-886 .187 Pin w/Groove 17-841 Cutter Head 17-887 .157 Pin 17-892 E-Clip 17-888 Tension Spring 17-845 Blade Clamp Plate 17-889 Trunion Pin 17-893 M3x12mm FHS 17-890...