Using The Cooktop; Control Lock; Cooktop Use; Using The Heaters - Sharp SCR3042FB Operation Manual

CONTROL LOCK

The Control Lock function prevents
unwanted operation, such as by small
children. The Control Lock Indicator
Light above the Control Lock keypad
indicates it is locked. When Control
Lock is deactivated, the indicator light
will turn off.
FIRST TIME USE OR POWER RESTORATION
When the cooktop is powered ON for the first time, or after
power is restored in the event of a power outage, Control Lock
will activate and the control panel will be locked.
Control lock must be deactivated to access the power ON/OFF
keypad and operate the cooktop.
Select the desired heating element by pressing the ON keypad,
then move the power level to 0 on the Power Curve selector.
CONTROL LOCK MAY BE ACTIVATED IN THE
FOLLOWING 2 CASES
1 When the cooktop main power is OFF.
If Control Lock is turned ON when the cooktop is OFF, all
keypads are locked, including main Power ON/OFF. Control
Lock must be deactivated to use the cooktop heaters.
2 When the cooktop is in use and one or more heaters is
active.
When Control Lock is turned ON during cooking, all func-
tions are locked EXCEPT: individual Heater OFF keypads,
cooktop power ON/OFF keypad and the Control Lock
keypad.
TO LOCK
Touch and hold Control Lock keypad for 3 seconds, a tone will
sound, and the Control Lock Indicator Light above the Control
Lock keypad will illuminate.
TO UNLOCK
Touch and hold Control Lock keypad for 3 seconds, a tone will
sound, the Control Lock Indicator Light will turn OFF. The
cooktop is in Standby mode.

COOKTOP USE

TURN ON THE COOKTOP
The cooktop is switched ON by touching the
ON/OFF keypad for 1 second. A tone will
sound, and all heater digital displays will
show "0".
TO TURN OFF THE COOKTOP
The cooktop is switched OFF by touching the ON/OFF keypad
for 1 second. A tone will sound, and all heater digital displays
will be turned OFF.
NOTE: If a heater is not selected within 10 seconds, the cooktop
will turn OFF automatically.
CONTROL CONTROL
LOCK - ON LOCK - OFF
13

USING THE COOKTOP

USING THE HEATERS

TURN ON HEATERS
Select desired heater and touch ON
keypad. A tone will sound, and the Hot
Surface/ON Indicator Light will blink.
NOTE: Heater selection will complete
10 seconds after the last keypad is touched (ON, Power Slider
Bar, Bridge, Double, Speed Boil or Precise Low).
POWER LEVEL SELECTION
Select desired power level by
sliding finger across the Power
Slider Bar, moving toward the right to increase power level.
The selected power level will be shown in the Power Level
Digital Display of the heater and in the Power Curve display in
the center of the cooktop display. The lights on the Power Curve
display illuminate 2 segments at a time as the power level is
selected. (See section PRECISE LOW POWER for information
on specific temperature control for delicate foods.)
Lowest Power Level Setting - 1
Highest Power Level Setting - 9
A power level between 1 and 9 must be selected regardless of any
other keypad pressed (e.g., the BRIDGE or TIMER +/- keypads).
If no power level is selected, the heater will automatically turn
OFF in 10 seconds.
NOTE:
• If two or more finger touches are detected, the selector will
default to the highest power setting.
• If the Control Lock is activated, the Power Slider Bar will
be locked.
POWER LEVEL ACCEPTANCE
After power level is selected, a tone will sound, the Hot Surface/
ON Indicator Light will stop blinking and remain on. Touch the
heater ON keypad again to accept the level and begin cooking,
or select Bridge, Double, Speed Boil or Precise Low (see Auto
Features section for details on these functions).
If no other keypad is touched within 10 seconds, the power level
will be accepted automatically. If another heater is selected, the
power level will be accepted on the current heater automatically.
E