Assembly; Unpack Pressure Washer; Attach Handle; Install Wheel Kit - Briggs & Stratton BPW2000 Operator's Manual

assembly

read entire operator's Manual before you attempt to assemble or operate
your new pressure washer.
Your pressure washer requires some assembly and is ready for use after it has been
properly serviced with the recommended oil and fuel.
If you have any problems with the assembly of your pressure washer, contact your local
Briggs & Stratton service center. If you need assistance, please have the model, revision,
and serial number from the identification label available. See Features and Controls for
identification label location.

unpack Pressure washer

1. Set the carton on a rigid, flat surface.
2. Remove the parts bag, accessories, and inserts included with pressure washer.
3. Open carton completely by cutting each corner from top to bottom.
4. Ensure you have all included items prior to assembly.
items in the carton include:
• Main Unit
• Handle
• High Pressure Hose
• Spray Gun
• Adjustable Nozzle Extension
• Wheels (2)
• Parts Bag (which includes the following):
• Operator's Manual
• Hose Fittings
• Maintenance Kit
• Accessory Storage Bag
• Handle/Wheel Kit Fastening Hardware Kit (which includes):
• Carriage Bolts (2)
• Plastic Knobs (2)
• Axle Pins (2)
• Retaining Pins (2)
to prepare your pressure washer for operation, you will need to perform these tasks:
1. Attach handle and wheel kit to main unit.
2. Add oil to engine crankcase.
3. Add fuel to fuel tank.
4. Connect high pressure hose to spray gun and pump.
5. Connect water supply to pump.
6. Attach nozzle extension to spray gun.
2
attach Handle Figure
1. Place handle (a) onto base (B). Make sure holes in handle align with holes on
base.
2. Insert carriage bolts (c) through holes from outside of unit and attach a plastic
knob (d) from inside of unit. Tighten by hand.
3
install wheel kit Figure
The wheel kit is designed to greatly improve the portability of your pressure washer.
NOTICE Wheel kit is not intended for over-the-road use.
install the wheel kit as follows:
1. Place the bottom of the pressure washer frame on a flat, even surface.
2. Slide a wheel (a) over the axle pin (B).
NOTICE Be sure to install wheel with raised hub inboard.
3. Slide axle pin through hole (c) in frame.
4. Retain wheel on axle pin with retaining pin (d).
5. Repeat step 2 through 4 to secure second wheel.

add engine oil

1. Place pressure washer on a level surface.
2. Add engine oil as described in Adding Engine Oil of the Engine Maintenance
section.
NOTICE Improper treatment of pressure washer could damage it and shorten its life.
• DO NOT attempt to crank or start the engine before it has been properly serviced
with the recommended oil. This could result in an engine failure.
4
add Fuel Figure
Fuel must meet these requirements:
• Clean, fresh, unleaded petrol.
• A minimum of 87 octane/87 AKI (91 RON). For high altitude use, see High
Altitude.
• Petrol with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary
butyl ether) is acceptable.
NOTICE Avoid pressure washer damage.
Failure to follow Operator's Manual for fuel recommendations voids warranty.
• DO NOT use unapproved petrol such as E85.
• DO NOT mix oil in petrol.
• DO NOT modify engine to run on alternate fuels.
To protect the fuel system from gum formation, mix in a fuel stabilizer when adding fuel.
See Storage. All fuel is not the same. If you experience starting or performance problems
after using fuel, switch to a different fuel provider or change brands. This engine is
certified to operate on petrol. The emission control system for this engine is EM (Engine
Modifications).
warning Fuel and its vapors are extremely flammable and explosive which
could cause burns, fire or explosion resulting in death, serious
injury and/or property damage.
wHen adding FueL
• Turn pressure washer engine OFF and let it cool at least 2 minutes before
removing fuel cap. Loosen cap slowly to relieve pressure in tank.
• Fill fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Check fuel lines, tank, cap and fittings frequently for cracks or leaks. Replace if
necessary.
• DO NOT light a cigarette or smoke.
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel (a) to fuel tank (B). Be careful not to overfill.
Allow about 4 cm (1.5") (c) of tank space for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate before starting engine.
High altitude
At altitudes over 1500 meters (5,000 feet), a minimum 85 octane / 85 AKI (89
RON) petrol is acceptable. To remain emissions compliant, high altitude adjustment
is required. Operation without this adjustment will cause decreased performance,
increased fuel consumption, and increased emissions. See a Briggs & Stratton
Authorized Dealer for high altitude adjustment information. Operation of the engine at
altitudes below 750 meters (2,500 feet) with the high altitude kit is not recommended.
5
Lubricate o-rings Figure
Lubrication of o-rings is extremely important for installation and operation. The use
of a lubricant (petroleum or synthetic grease) during assembly helps seat o-rings
properly and provides an improved seal. It also helps protect the o-ring from damage
by abrasion, pinching or cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant on o-rings prior to assembling
the garden hose to the pump (a), high pressure hose threaded end (B), spray gun (c),
and high pressure hose quick connect end (d).
Lubricate all connections shown below, following these instructions:
1. Inspect and clean connecting surfaces prior to lubrication and assembly.
2. Use lubricants sparingly during assembly; a light film is all that is required.
3. Use a small brush or cotton swab to apply grease directly to o-rings where they
are not accessible (QC fitting, M22 fitting).
7