Motion Sensor; Timer-To-Close (Ttc) - Chamberlain MyQ 889LM Manual

FUNCTIONS
Push Bar
Learn LED
(Red)
LEARN
button
LOCK
button
1 Minute
TTC LED
5 Minute
TTC LED
10 Minute
TTC LED
PUSH BAR
Press the push bar to open or close the door.
LIGHTS
Press the LIGHT button to turn the garage door opener lights on or off. When the
lights are turned on they will stay on until the LIGHT button is pressed again, or
until the garage door opener is activated. Once the garage door opener is activated
the lights will turn off after the specified period of time (the factory setting is 4-1/2
minutes). The LIGHT button will not control the lights when the door is in motion.
To change the amount of time the garage door opener lights will stay on:
Press and hold the LOCK button until the garage door opener lights flash.* The
time interval is indicated by the number of flashes.
NUMBER OF TIMES GARAGE
TIME THE GARAGE DOOR OPENER LIGHT STAYS ON
DOOR OPENER LIGHTS FLASH
1
2
3
4
To cycle through the time intervals repeat the step above.
* Approximately 10 seconds
Light Feature (Default is Active)
The lights will turn on when someone enters through the open garage door and the
safety reversing sensor infrared beam is broken.
Deactivate:
Press and hold the LIGHT button until the garage door opener lights turn on,
then off again.*
Activate:
Start with the garage door opener lights on. Press and hold the LIGHT button
until the garage door opener lights turn off, then on again.*
Command
LED (yellow)
ON Button
OFF Button
HOLD OPEN
Button
LIGHT
Button
Motion
Sensor
1 ½
Minutes
2 ½
Minutes
3 ½
Minutes
4 ½
Minutes
3

MOTION SENSOR

This feature will automatically turn on the garage door opener lights when motion
is sensed. The lights will come on for the set period of time, then shut off.
Activate/Deactivate:
Slide the motion sensor switch ON or OFF.

TIMER-TO-CLOSE (TTC)

NOTE: DO NOT install this door control on garage door opener systems controlling one-
piece or swing doors.
The TTC feature automatically closes the door after a specified time period (1, 5, or
10 minutes). Once the TTC has been set and the door is open, the LED for the
selected close interval will blink and begin to count down to close the door. The
control panel will beep and the garage door opener lights will flash before closing
the door.
The TTC feature will deactivate if the garage door encounters an obstruction twice;
or the safety reversing sensors are incorrectly installed. The garage door will
reverse open and WILL NOT close until the obstructions are clear or the safety
reversing sensors are correctly installed. When the obstruction has been cleared or
the safety reversing sensors have been aligned, the door will close when the
garage door opener is activated.
Activate:
Press and hold the ON button until one of the TTC LEDs light up. Then press the
ON button again to cycle through the time interval options (the corresponding
TTC LED will light for each time interval). The garage door opener light bulbs
will blink as confirmation.
Deactivate:
Press and hold the OFF button until all TTC LEDs turn off and a beep is heard
from the control panel.
Temporarily hold door open (suspend TTC):
Press and release the HOLD OPEN button. The HOLD OPEN button will begin to
flash. Press the HOLD OPEN button again to resume normal TTC operation.
LOCK
Your remote controls will NOT work when LOCK mode is active, however your
keyless entry will still allow access to your garage.
Activate*:
Press and hold the LOCK button for 2 seconds. The command LED will flash as
long as the lock feature is activated and your handheld remote control will not
operate your door at this time.
Deactivate:
Press and hold the LOCK button again for 2 seconds. The command LED will
stop flashing and normal operation will resume.
* Your LiftMaster keypad will continue to work when the LOCK has been
®
activated.