Related Manuals for Digilin Colour Touch VW
Summary of Contents for Digilin Colour Touch VW
- Page 1 Colour Touch VW VW DMX Controller FW 1.0 User Manual ©2021 Digilin Technologies Document Rev: 1.0 - 2 June 2021 Product specifications are subject to change without notice...
-
Page 2: Table Of Contents
Colour Touch VW - VW DMX Controller FW 1.0 User Manual 1.0 - 2 June 2021 Table Of Contents Notes ............................................................. 2 Introduction ........................................................3 Specifications ......................................................4 Physical ........................................................4 Inputs ..........................................................4 Communications ..................................................... 4 Installation ........................................................5 Wiring ........................................................... -
Page 3: Introduction
1.0 - 2 June 2021 Introduction The Colour Touch VW Controller is a DMX show generator with a simple and intuitive user interface, specifically designed for use with Digilin’s LED VariWhite Driver to control installations of tuneable white LED fittings. Tuneable white fittings allow the user to set the colour temperature through a set range of values, thus allowing the user to set the mood and ambience of an area by controlling the colour temperature of the white light. -
Page 4: Specifications
Colour Touch VW - VW DMX Controller FW 1.0 User Manual 1.0 - 2 June 2021 Specifications Physical U n i t s Front Plate Dimensions 76 x 116 x 10.6 Protrusion Dimensions (less 50 x 75 x 21.9 cabling) -
Page 5: Installation
Table 1 Wiring to Cat5 cables Mounting The Colour Touch VW Controller is housed in a standard Clipsal plate, and as such is compatible with any standard mounting boxes or clips. There is also a mounting frame (Clipsal Part number 4000VH1) available in 5 colours that can be used to cover the black base and compliment wall colour. -
Page 6: Operation
Dimming Each show on the Colour Touch VW can have a dimming multiplier of 1-100%, this can be controlled via the “Dim” menu. to access the Dim menu, use the left and right keys until “Dim” is displayed on the Colour Touch. -
Page 7: Switching Drivers Off/On
Power on State Upon applying power to the Colour Touch VW, the controller will apply a snapshot of values to the dim and CCT. This is known as the power on state. This can be configured in the settings menu. Each setting is described in Table 2. - Page 8 Upon leaving the settings menu the control will save it to memory. Adjusting the Power on State The power on state controls what configuration to apply to the Colour Touch VW at power on. once the setting menus is enabled, the power on state can be adjusted.
-
Page 9: Performing A Factory Reset
Performing a Factory Reset The Colour Touch VW is fitted with a factory reset button on the back of the device. This is only accessible after the device has been remove from front faceplate and device is on. To perform the factory reset follow the steps below. -
Page 10: Appendix A. Wiring Diagram With Lcthm Power
Colour Touch VW - VW DMX Controller FW 1.0 User Manual 1.0 - 2 June 2021 Appendix A. Wiring Diagram with LCTHM Power DMX Communication + LCTHM power To Driver DMX input Cat5 RJ45 Cable To Controller digilin.com.au Page 10 of 11... -
Page 11: Appendix B. Wiring Diagram With Aux Power
Colour Touch VW - VW DMX Controller FW 1.0 User Manual 1.0 - 2 June 2021 Appendix B. Wiring Diagram with AUX Power DMX Communication To Driver DMX input Cat5 RJ45 Cable To Controller Aux Power In input digilin.com.au Page 11 of 11...
Need help?
Do you have a question about the Colour Touch VW and is the answer not in the manual?
Questions and answers