Toshiba SD-46VSR Service Manual page 10

One-Touch Timer Recording (OTR)
The one-touch timer recording feature Preparation
provides a simple and convenient way • Turn ON the TV and set to the AV input mode.
to make a timed recording. • Press VCR to select the VCR mode. (The VCR indicator will
light.)
1
Load a blank cassette tape with the erase
prevention tab intact. (The DVD/VCR will
automatically turn on.)
2
Select the program(e.g.29) you want to record with CH +/– or
number buttons.
1~9 :
10~80 : e.g. 29 = press "2" and "9".
3
If a recording in Long Play mode
is intended, press SP/LP to dis-
play "LP".
4
Press REC/OTR twice. The recording will start and stop after 30
minutes. Each additional press of
REC/OTR will increase the record-
ing time to a maximum of 6 hours
(See table below).
If REC/OTR is pressed once during the recording, the remain-
ing time appears on the screen. When pressed again, the re-
cording time is extended to the nearest 30-minute or 1-hour
interval.
To Extend the Recording Time
Press REC/OTR repeatedly until the
Note:
desired time appears on the display.
If the tape supply has not sufficed for OTR
recording, the clock symbol ( ) will blink
at the tape-end and then VCR mode will
change to DVD mode.
In this case, press TIMER REC to cancel
the blink or press EJECT on the DVD/
To stop the OTR
VCR to remove the cassette tape.
Press STOP.
32
Timer Recording
5
Press ENTER to accept them.
To enter other pro-
13:00 14:30 1
23 MON LP
------ --:-- --:-- -- -
grams, repeat steps
------ --:-- --:-- -- -
------ --:-- --:-- -- -
2 through 5.
------ --:-- --:-- -- -
------ --:-- --:-- -- -
------ --:-- --:-- -- -
• To return to the
------ --:-- --:-- -- -
normal screen,
SELECT : / ENTER
EXIT : MENU
press VCR MENU
twice.
6
Press TIMER REC. The clock symbol ( ) will
appear on the display and the DVD/VCR stands by
for recording. At the same time, VCR mode will
change to DVD mode automatically. You can use
DVD even if the VCR is in the Timer recording mode.
If you do not use the DVD, turn the power off.
• If the clock symbol ( ) blinks in the display in
spite of the pressing of TIMER REC, the cassette
may not have been loaded yet. (see page 24)
• If the cassette is ejected in spite of the pressing
of TIMER REC, the erase prevention tab of the
cassette may have been removed. (see page 24)
Notes:
• In case of the timer recording from the scart socket,
proceed as follows: In step 4 press or repeatedly
until the "CH" line blinks. Then press AUX repeatedly
until "AV1" or "AV2" or "AV3" appears.
• If the clock symbol ( ) blinks when the timer recording
ended, the TV program has not been completely
recorded because of an insufficient tape supply. Press
TIMER REC to cancel the timer program or press
EJECT on the DVD/VCR to remove the cassette tape.
• During timer recording standby mode, the VCR mode
cannot be selected. To use the VCR, press TIMER
REC at first, then press VCR to change to VCR mode.
After you use the VCR, press TIMER REC again to put
the VCR into timer recording standby mode.
Timer Recording Special Case
Weekly (e.g. WKL-TUE: each Tuesday) or daily (e.g.
MON-SAT: Monday to Saturday) Timer recording
Follow the procedure for timer recording on page 33. At
picture 3 press or repeatedly until the desired
setting appears. Then press . When you press or
repeatedly, the indicator at DATE will change as
follows, in case today is Friday.
One month later
minus one day
SUN-SAT 25 FRI ..... 24 SUN WKL-FRI
MON-SAT MON-FRI WKL-THU.....WKL-SAT
TIMER REC SET
DATE WKL-WED
START 11:30
- - : - -
END
MON-SAT = everyday from CH 2
SPEED
SP
Monday to Saturday
SELECT :
WKL-SAT = each Saturday
SET : / 0-9
EXIT : MENU
34
VCR
e.g. 5 = press "5"
VCR
00:00:00 LP
OTR 0:30
CH 29
VCR
INDEX
REC
"REC" will keep blinking
in the display.
1:30
Recording 0:30 1:00
3:00 2:00
6:00 5:00 4:00
OTR 1 : 30
CH 29
In case of Timer programs-overlapping
Do not overlap timer programs as portions of the
conflicting programs will be lost. The first recording
time has priority over the next recording time as
shown in the diagram below.
8 : 00 9 : 00
10 : 00 11 : 00
Program 1
Program 2
Deleted Parts
Program 3
Non Recorded Portion Parts
Recording
Prog.1 Prog.2 Prog.3
Control Settings
Notes:
• The daily/weekly recording can be made continuously until
the recording is canceled or the tape reaches the end.
• During timer recording the automatic rewinding mecha-
nism does not function.
Confirmation / Cancellation of the Timer
Recording
1
If the Timer has been activated, now press TIMER
REC to deactivate the Timer. The clock symbol ( )
will disappear. Then press VCR to change to VCR
mode.
2
Press PROGRAM. All the 8 Timer memories will
appear.
15 TUE 17:30 18:00 7 SP
23 MON 13:00 14:30 1 LP
25 WED 12:15 13:00 4 SP
------ --:-- --:-- -- -
------ --:-- --:-- -- -
------ --:-- --:-- -- -
------ --:-- --:-- -- -
------ --:-- -- -
--:--
SELECT : / ENTER
CLEAR : CANCEL EXIT : MENU
3
To cancel Timer program: Press or to select
the written line. Then press CANCEL. This line is
now canceled.
------ --:-- --:-- -- -
23 MON 13:00 14:30 1 LP
25 WED 12:15 13:00 4 SP
------ --:-- -- -
--:--
------ --:-- -- -
--:--
------ --:-- --:-- -- -
------ --:-- --:-- -- -
------ --:-- --:-- -- -
SELECT : / ENTER
EXIT : MENU
4
Press VCR MENU (or PROGRAM) repeatedly until
the TV-picture appears.
Preparation
Timer recording can be programmed
on the TV-screen with the remote con-
• Turn ON the TV and set to the AV input mode.
trol. The built-in timer allows automatic
• Press VCR to select the VCR mode. (The VCR indicator will light.)
unattended recording of up to 8 pro-
• Load a video cassette with the erase prevention tab intact. Make
grams within 1 month.
sure with CALL that the time and date are correct.(see page 31).
Example: Timer recording for channel 1, 13:00 to 14:30 with Tape
speed LP on timer program number 1.
1
Press VCR MENU. Press
to select TIMER REC SET.
Then press ENTER.
2
Each line stands for one pro-
gram of the 8 memories. Select
one line with
press ENTER.
3
Set the desired date with
or number buttons. Then
press
4
Set the Starting time (13:00),
ending time (14:30), channel
(1) and Tape speed (LP) in the
same way as the step 3.
• In case of an erroneous input
press
step and enter again.
Note:
In the event of a power failure the data of
the automatic recording will be maintained
in the built-in memory for about 30 min-
utes. Also, the clock will continue to run for
this period of time. Thereafter the data will
be deleted. When the power resumes, the
time display will change to "--:--" that the
timer setting will have to be set.
Stereo Recording and Playback
This DVD/VCR is capable of recording Preparation:
sound in Hi-Fi system. The recording
• Turn ON the TV and set to the AV input mode.
will be performed automatically.
• Press VCR to select the VCR mode. (The VCR indicator will light.)
NICAM STEREO broadcasts are
recorded in its original sound system
NICAM stereo sound reception:
regardless of the setting. If you wish
to record NICAM programmes, select
NICAM "AUTO" as follows.
1
Press VCR MENU. Press
And, this DVD/VCR can also receive
to select VCR SETUP.
and record German A2 stereo pro-
Then press ENTER.
gram. The tape recording is always
both in Hi-Fi and in MONO on the
standard longitudinal track. In case of
bilingual TV programs always the two
audio channels will be recorded.
2
Press
Then press
select [AUTO].
3
Press VCR MENU repeatedly until the TV picture appears.
NICAM programmes are divided into 4 types as shown
below.
NICAM STEREO broadcast
"NICAM ST" illuminates when a NICAM
STEREO broadcast signal is received.
NICAM MONO A broadcast
"NICAM M1" illuminates when a NICAM
MONO A broadcast signal is received.
NICAM MONO A B broadcast
"NICAM M1/2" illuminates when a NICAM
MONO A and MONO B broadcast signal is
received.
NICAM OFF
Note:
It will be displayed for the NICAM signal
When listening to a stereo broadcast or
when the "NICAM [OFF]" is selected in
playing back a Hi-Fi tape recorded in
menu screen.
stereo, you have to connect the DVD/
VCR with the stereo audio system or the
stereo TV. The sound which is output
from the RF OUT jack is monaural.
Timer Recording
or
TIMER REC SET
AUTO REPEAT [OFF]
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER : ENTER
EXIT : MENU
------ --:-- --
--:-- -
------ --:-- --:-- -- -
------ --:-- --:-- -- -
or . Then
------ --:-- --:-- -- -
------ --:-- --:-- -- -
------ --:-- --:-- -- -
------ --:-- --:-- -- -
------ --:-- --:-- -- -
SELECT : / ENTER
EXIT : MENU
or
TIMER REC SET
DATE 23 MON
to accept it.
START 11:30
--:--
END
CH 3
SPEED SP
SELECT :
SET : / 0–9
EXIT : MENU
TIMER REC SET
DATE 23 MON
START
13:00
END 14:30
CH 1
SPEED LP
SELECT :
to go back to before
SET :
EXIT : MENU OK : ENTER
....to be continued to next page
33
or
TIMER REC SET
AUTO REPEAT [OFF]
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER : ENTER
EXIT : MENU
or to select NICAM.
VCR SETUP
/ or ENTER to
COLOUR SYSTEM [ AUTO]
NICAM [AUTO]
SELECT : /
ENTER : ENTER
EXIT : MENU
NICAM ST
NICAM M1
NICAM M1/2
NICAM OFF
35