Lanberg FF01 37U Series User Manual page 2

1. Important introductory recommendations and usage information
1.1 Introduction
Manual also contains logistic and technical data, instructions, and regulations that must be observed and complied with during
transport, assembly, use, and potential maintenance of the products. Under no circumstances should you use the device before
carefully reading and fully adapting to all information in the user's manual. Keep this manual for future reference. All photos, illustrations
contained in the instructions are for reference only. The information contained in this manual has been verified and is considered
sufficient. The supplier is not responsible for any inaccuracies that may be included in this document, nor is he responsible for updating
or keeping the current information in this manual, nor for notifying its users or organization about the updates. In particular, Lanberg
owners are not responsible for any equipment, software, or data stored/used with the product, including maintenance, replacement,
integration, installation, or recovery of hardware, software, or data in the event of misuse of the product or its components.
Lanberg brand owners reserve the right to make changes to this manual at any time without notice. The products mentioned in this
manual, including the documentation, are the property of the Lanberg brand owners and its licensors. Any use or reproduction of
these products, including documentation, is prohibited, except as expressly authorized under the appropriate license terms.
NOTE: For the most up-to-date version of this manual, please visit our website at www.lanberg.eu.
1.2 Compliance with legal and regulatory provisions regarding safety and the environment
This product complies with EU safety and environmental regulations.
The products listed in the following instructions have been approved for trading within the EU, by obtaining a European Union
Declaration of Conformity, which contains a declaration with the essential requirements and other relevant provisions of the following
Directives, and that the following harmonized standards have been applied.
Directive: RoHS 2011/65/UE + 2015/863/UE
Standards: IEC 62321-4:2013 + A1:2017; IEC 62321-5:2013;
IEC 62321-6:2015; IEC 62321-7-2:2017; IEC 62321-8:2017;
With the development of products and updates to CE regulations, the declaration may change. The latest declaration of conformity
(CE) can be found at: www.lanberg.eu.
NOTE: The use of the WEEE symbol (crossed-out wheelie bin symbol) means that this product cannot be treated as household waste.
Proper disposal of used equipment avoids risks to human health and the environment, resulting from the possible presence of
hazardous substances, mixtures, and components in the equipment, as well as improper storage and processing of such equipment.
The selective collection also allows you to recover materials and components, from which the device was manufactured. For more
information about the recycling of this product, please contact the retail outlet, where the product was purchased, or request
information from the local authority.
1.3 General safety precautions
• The device specifications must be strictly observed when using the product and connecting it to any external products. The
specifications of the external devices to which this device is to be connected must also be observed.
• The product cannot be used outside of the rated values in its specification. The warranty does not cover any damage caused by
a deviation from these values when using the device.
• All installations, connections, cabling, and circuits in which the product will be used must be made in a manner consistent with
locally applicable electricity regulations and in such a way as to eliminate the risk of people walking or tripping over them. Use
only power cables with VDE and CE certification when connecting them to the device. It is necessary to use the same procedures
mentioned in this section when connecting the cabling to the product or to the external components.
• For external devices connected to this product, the operating instructions supplied by their manufacturer must be strictly observed.
• To ensure safety and compliance of the device, use only components or parts that meet the specifications or are recommended by
the manufacturer.
• During the warranty period, it is forbidden to replace any elements of the product by its users. Maintenance should be entrusted
only to qualified technical personnel, such as the manufacturer's technical department or an authorized importer.
• If it is necessary to perform maintenance of the device, it should be carried out or supervised by a person having appropriate
qualifications and technical knowledge about the device, while maintaining proper precautions. All this under the local regulations
in force.
• If it is necessary to perform maintenance of the equipment or similar activities that will require opening the device or contact with
elements that may be under potential voltage, the following safety rules should be observed before carrying out these activities:
remove all bracelets, necklaces, rings, watches or other metal hand and neck objects and use tools with insulated handles.
• Always before performing the equipment maintenance, there should be a person nearby who would react and take appropriate
steps to assist the person in charge of the device maintenance in the event of an accident. A person undertaking the maintenance
should always wash hands after finishing his / her work.
• NEVER allow a situation where sparks or flames could occur near the device. The aftermath of such a situation could have very
negative consequences for people and things in the vicinity.
• In the event of a fire, immediately and (without unnecessary delay) disconnect the power supply and notify the fire department of
the situation by dialing their assigned emergency number in the country of your stay.
• The product is intended for indoor use. Do not rebuild and/or modify the products and/or their components.
• Under no circumstances, other external products are to be introduced (connected to the device), that are non-compliant with the
EN Lanberg © 2015-2021
1