Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JC BORDELET EVA992GAZ
Summary of Contents for JC BORDELET EVA992GAZ
-
Page 3: Safety Warnings
IMPORTANT INFORMATION SAFETY WARNINGS INSPECTION ON ARRIVAL Check the appliance immediately on arrival. Only a qualified installer should install the appliance. The Make sure that the appliance is correct for the type of gas appliance must be installed in accordance with the obligatorily and the combustion product evacuation system as indicated instructions attached to the appliance, with the statutory on the nameplate of the appliance and on the gas settings... -
Page 4: Technical Characteristics
TECHNICAL CHARACTERISTICS NATURAL GAS - NG LV CY ES PT HU RO GR HR EE FI IT LT CZ Country FR BE DE LU PL RO GB SI SK AT DK IE SE CH TR NO Category I2E+ I2EK I2ELL Gas type G20/G25 G25.3... - Page 5 TECHNICAL CHARACTERISTICS OF THE FREE STANDING APPLIANCE GENERAL COMPOSITION GENERAL DIMENSIONS OF THE APPLIANCE HOOD Standard paint or lacquered finish Ø816mm FIREPLACE Natural Gas Liquefied Petroleum Gas Ø600mm Ø1175mm BASE Metal ACCESS HATCH Must remain Brick accessible Ceramic TECHNICAL CHARACTERISTICS OF THE WALL-MOUNTED APPLIANCE GENERAL COMPOSITION GENERAL DIMENSIONS OF THE APPLIANCE HOOD...
-
Page 6: Installation Of The Appliance
INSTALLATION OF THE APPLIANCE DETERMINING THE FLUE CONFIGURATION INSTALLATION OF THE BASE Make a diagram of the desired layout of the concentric flue Place the base on a flat floor. The appliance has 4 height- system. adjustable feet. Respect the required distances from flammable materials and Please make sure to comply with distances from inflammable the position of permitted outlets as described below when materials as provided in the technical characteristics and... - Page 7 INSTALLATION OF THE APPLIANCE INSTALLATION OF THE BASE PLATES C91 Configuration = Ø100/150 Mandatory nozzle adapter: A130/200SEGDG The base plates are to be attached using the bolts provided. Mandatory reduction: RC100/150-130/200DG The counter-sinks should be upwards to accept the heads. Mandatory vertical terminal: CTIV G 100 DG Square ceiling starting kit: KRFL C 100 DG Rectangular ceiling starting kit: KRFL R 100 DG...
- Page 8 INSTALLATION OF THE APPLIANCE The position of outlets must be as follows [H] Re-entrant angle walls Without opening With opening [A] Opening [B] Air inlet [D] Below balcony and Roof edge [J] Outings in an [K] Two exits on the [C] Distance above ground interior courtyard same wall...
-
Page 9: Connecting Gas
INSTALLATION OF THE APPLIANCE After installing the hood and the ducts, it is necessary to Measured Description Abbreviation verify again that the valve can move freely. In order to do so, value lift it several times at the maximum from the inside of the Number of vertical metres …. - Page 10 INSTALLATION OF THE APPLIANCE Log 6 (x2) The solenoid valve block and the power cord are behind the Composition of the log set: base trapdoor. The gas pipe must be purged before proceeding to the connection. The installation of the gas supply must be done by a qualified professional and the gas system must be compliant with decree of 23 February 2018 and with standard NF DTU 61.1 P1 to 7.
- Page 11 INSTALLATION OF THE APPLIANCE 1. INSTALLATION INSTRUCTIONS...
- Page 12 INSTALLATION OF THE APPLIANCE Begin by installing the bottom centre fastening (1) of the glass screen (1) located above the base hatch. Fit the glass and then put in the top centre fastening. Tighten so as to allow some movement of the glass. This movement will be used for centering the windows once the assembly is pre-assembled.
-
Page 13: Annexe 1: Troubleshooting
ANNEXE 1: TROUBLESHOOTING NO SPARK THE APPLIANCE SWITCHES OFF No power supply Make sure that the gas tap is open. Make sure that the appliance is correctly connected. Check the gas supply pressure. Adjust the gas pressure if Make sure that the breaker in the central electric board is needed. -
Page 16: Maintenance Of The Appliance
- there is a risk of a short-circuit or WARRANTY electrocution. Your JC BORDELET appliance is covered by warranty. Floors, shelves and walls close to the appliance must be All warranty conditions can be found in the “WARRANTY”... -
Page 17: Using The Remote Control
USING THE REMOTE CONTROL USING THE REMOTE CONTROL The following programs are available*: The remote control has been specifically designed to work A program with identical settings for each day with the gas inflow control system in your appliance. It has A program with different settings for the days of the week been adjusted by us to ensure your fireplace works correctly. - Page 18 USING THE REMOTE CONTROL If the fireplace, the receiver or the remote control are Adjusting the flame height replaced, the remote control must be registered manually, Press the button once. The screen below will Procedure for remote control recognition. appear. The flame height setting will flash.
- Page 19 USING THE REMOTE CONTROL Programmer NB: to exit the user menu, press the button or wait five The temperature is set according to the current program, see seconds after the last button press. Setting the programmer . The fireplace is lit and turned off completely automatically Manually setting the programmer Temporarily changing the temperature setting...
-
Page 20: Installation Menu
USING THE REMOTE CONTROL Wait a few seconds or press the button to exit the menu. Use the buttons to select the desired number of periods per day (II, IV or VI) INSTALLATION MENU Wait a few seconds or press the button to exit the menu. - Page 21 USING THE REMOTE CONTROL Malfunction of the temperature sensors Figure 1 of the remote control and the fireplace (or sensor in the latter unavailable). Operation and the adjustment of the flame height are automatically switched to manual mode. Resolving the locking problem. You can solve problems associated with the fireplace locking up (the word reset appears).
- Page 22 ANNEXE 1: TROUBLESHOOTING NO SPARK THE APPLIANCE SWITCHES OFF No power supply Make sure that the gas tap is open. Make sure that the appliance is correctly connected. Check the gas supply pressure. Adjust the gas pressure if Make sure that the breaker in the central electric board is needed.
-
Page 23: Warranty
WARRANTY BENEFICIARY This warranty is transferable from owner to owner, but proof This warranty applies to any purchaser of an EVA992GAZ of the original purchase is required. This warranty does not appliance. It shall become effective on the date of delivery at limit our legal responsibility for faults or hidden defects. - Page 25 Nameplate of your appliance...
- Page 26 ZI de Lhérat 63310 RANDAN Tél: 0470561600 – Fax : 0470561689 www.bordelet.com...
Need help?
Do you have a question about the EVA992GAZ and is the answer not in the manual?
Questions and answers