Advertisement
Quick Links
2XX-IP
ETHERNET INTERFACE OPTION
For 200 Series Indicators
(205/210, 212G/212GX and 225)
INSTALLATION MANUAL
8200-M503-O1 Rev B
203 E. Daugherty, Webb City, MO 64870 USA
Printed in USA
Ph: 417-673-4631 Fax: 417-673-2153
10/14
http://www.cardinalscale.com
Technical Support: Ph: 866-254-8261 • tech@cardet.com
8200-M503-01 Rev-B • 2XX-IP
1
Advertisement
Related Manuals for Cardinal 2XX-IP
Summary of Contents for Cardinal 2XX-IP
- Page 1 For 200 Series Indicators (205/210, 212G/212GX and 225) INSTALLATION MANUAL 8200-M503-O1 Rev B 203 E. Daugherty, Webb City, MO 64870 USA Printed in USA Ph: 417-673-4631 Fax: 417-673-2153 10/14 http://www.cardinalscale.com Technical Support: Ph: 866-254-8261 • tech@cardet.com 8200-M503-01 Rev-B • 2XX-IP...
- Page 2 8200-M503-01 Rev-B • 2XX-IP...
-
Page 3: Specifications
It is based on a Lantronix XPort® - Embedded Ethernet Device Server module and resides in the indicator main enclosure. The purpose of this manual is to provide you with a guide through installation of the 2XX-IP Ethernet Interface Option. Please read it thoroughly before attempting to install the option card in your indicator and keep it handy for future reference. -
Page 4: Installation
2XX-IP board (with P7 pins on bottom side). 8. Align the hole in the 2XX-IP board with the threaded stand-off on the indicator main board and using the lock washer and screw supplied with the 2XX-IP board, secure the 2XX-IP to the indicator main board. - Page 5 INSTALLATION, CONT. Mounting the 2XX-IP Option Card, Cont. 205/210/212G/212GX Main PCB NOTE: 205 Main PCB shown. The 210/212G/212GX Main PCB will have connector P2, REMOTE OUTPUTS and J7, REMOTE OUTPUT SRC jumper installed. THREADED STAND-OFF OPTIONB OARD THREADED STAND-OFF OPTION...
- Page 6 Allow an adequate length of exposed wires to reach the 2XX-IP Ethernet port (without being tight) after it has been terminated. 7. Next, cut the shield wire so that it extends past the outer jacket approximately 3/4 inch.
- Page 7 10. Do not over-tighten the connector but make certain it is snug. 11. Consult your network administrator for the proper procedure to terminate the cable. 12. After the cable has been terminated, plug the cable into the Ethernet port on the 2XX-IP. Re-Installing the 205/210 and 225 Rear Panel After all terminations have been made;...
- Page 8 205/210/212G/212GX INDICATOR SETUP A new section has been added to the SETUP menu for the 2XX-IP board. The new sub menu Option (Option) has been placed after LoCoUT (Key Lock Out Function). The Option sub menu contains the setup required to establish communications.
- Page 9 4. 2XX-IP 5. BADGE RDR Enter Selection: 0 PREV EXIT Press the 4 key and then the ENTER key, the 2XX-IP SETUP MENU will be displayed. 2XX-IP SETUP MENU 1. CONT=XXX 2. TYPE=X XXXXXXXXX 3. SCALE = 0 Enter Selection: 0 EXIT 1.
- Page 10 225 INDICATOR SETUP, CONT. 2. TYPE=X To select the format of the data transmitted from the 2XX-IP card, press the 2 key and then the ENTER key. 2XX-IP CONTINUOUS OUTPUT SELECTION 0. SMA 5. SB500 1. SB400 6. SB250/500M 2. TOLEDO 3.
-
Page 11: Troubleshooting
TROUBLESHOOTING Status LED’s The 2XX-IP contains two LED’s to indicate the communication status of the 10/100BaseT Ethernet TCP/IP connection. ETHERNET LINK (D3) - This LED will illuminate when the 2XX-IP has been successfully connected to a network and flicker when data is being transmitted or received over the network. - Page 12 8200-M503-01 Rev-B • 2XX-IP...