Advertisement
SYMBOLOGY
Volts
Direct Current
Alternating Current
Double Insulated
Read Operator's Manual
Do not stare at the
operating light source.
Regulatory Compliance mark
(RCM). This product meets
applicable
requirements.
Do not dispose of electric tools
together with household waste
material.
electronic equipment that have
reached the end of their life must
be
collected
returned to an environmentally
compatible recycling facility.
SPECIFICATIONS
Cat. No. ................................................ M18 HOAL
Battery Type .................................................M18™
Charger Type................................................M18™
AC Input Volts .................................... 220-240V AC
Hertz .........................................................
AC Input Amps.................................................
DC Input Volts............................................. 18V DC
DC Input Amps................................................. 36W
Recommended Ambient
Operating Temperature .................... -17°C to 51°C
EXTENSION CORDS
Extension cords should be selected with care.
•
Before use, the extension cord should be carefully
•
inspected to ensure there is no damage to the
cord, plug or connector. Replace a damaged
extension cord immediately or have it repaired by a
qualified electrical worker.
•
Select an extension cord suitable for the job.
Having excess length of cord can present an
unnecessary trip hazard.
•
Select a suitable cord for the product. Ensure that
the light and cord are not exposed to water, sharp
objects or mechanical hazards.
•
Extension cords should be selected so that there is
not an excessive length used.
extension cord, the greater the voltage drop over
the length of the cord and the performance of the
light can be reduced.
•
Recommended maximum extension cord lengths
for this light are:
- 1.0mm
25m
2
- 1.5mm
35m
2
regulatory
Electric
tools
and
separately
and
50-60 Hz
The longer an
WARNING
For specific charging instructions, read the
operator's manual supplied with your charger
and battery.
Inserting/Removing the Battery
Insert the battery pack by sliding battery pack into
the tool. Insert the battery pack until the battery
latches lock.
Inserting/Removing Power Cord
To operate on AC power, connect a suitable
extension cord to the AC inlet. To remove, unplug
the extension cord from the inlet.
WARNING
may be hazardous.
CAUTION
Press and hold the ON/OFF button
Use the MODE button to cycle through High, Medium,
Low. Press and hold the ON/OFF button
OFF immediately. Rotate light head to desired angle.
WARNING
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE
Keep your tool in good repair by adopting a regular
maintenance program. Inspect your tool for issues
such as undue noise, misalignment or binding of
50W
moving parts, breakage of parts, or any other
condition that may affect the tool operation. Return
the tool to a MILWAUKEE
After six months to one year, depending on use,
return the tool to a MILWAUKEE
inspection.
WARNING
immerse your tool, battery pack or charger in
liquid or allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain
cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include
gasoline, turpentine, lacquer thinner, paint thinner,
chlorinated
cleaning
household detergents containing ammonia. Never
use flammable or combustible solvents around
tools.
For repairs, return the tool, battery pack and charger
to the nearest authorised service centre.
WARNING
For a complete listing of accessories, go online to
milwaukeetool.com.au / milwaukeetool.co.nz or
contact a distributor.
3
ASSEMBLY
Recharge battery only with the
charger specified for the battery.
Only use
accessorie
reco
mmended
for thi
OPERATION
T
o reduce the risk of injury
stare at the
operating light source.
MAINTENANCE
To reduce the risk of injury, always
unplug the charger and remove the
service facility for ALL repairs.
®
Maintaining Tools
service facility for repair.
®
service facility for
®
To reduce the risk of personal
injury
and
damage,
Cleaning
solvents,
Repairs
ACCESSORIES
Use only recommended accesso-
ries. Others may be hazardous.
s
s tool. Others
, do not
to turn ON.
to turn
never
ammonia
and
Advertisement
