Summary of Contents for Eurofred daitsu RHR-SCO2
- Page 1 USER MANUAL REMOTE CONTROL RHR-SCO2 Serie HEAT RECOVERY FRESHOME RHR Edition 03/21 Models RHR 150 RHR 200...
- Page 2 DAITSU RHR-S WIRELESS CO PROBE Country: EN Children over the age of 8, people with reduced physical or mental abilities and those with lit- tle knowledge or experience may use this system provided they are supervised or have re- ceived instructions on how to use the system safely and are aware of the associated dangers. Children below the age of 3 must be kept away from the system, unless they are always supervised.
-
Page 3: Table Of Contents
CONTENT 1 ABOUT THIS MANUAL .................... 1.1 About the device ....................1.2 How to use this manual ..................1.3 Original Instructions ....................1.4 Warnings ......................2 SAFETY ........................2.1 Directives ......................2.2 Signs on the unit ....................2.3 General safety instructions ..................3 DESCRIPTION ...................... -
Page 4: About This Manual
DAITSU WIRELESS CO PROBE / INSTALLATION AND OPERATION MANUAL LED status LED mode Touch button 1 ABOUT THIS MANUAL 1.1 ABOUT THE DEVICE probe is a user control and a CO sensor for the ventilation system. The device communicates information The wireless CO on the ventilation speed request and the system status via wireless communications with the central control device. -
Page 5: Safety
2 SAFETY 2.1 DIRECTIVES The device complies with the following EC directives: EMC Directive: 2004/108/EC Low Voltage Directive: 2006/95/EC RTTE Directive: 1999/5/EC RoHS Directive: 2002/95/EC WEEE Directive: 2002/96/EC 2.2 SIGNS ON THE UNIT Warning: Check the instructions for use as a precaution. Danger: Risk of electric shock. -
Page 6: Ventilation Speeds And Modes
DAITSU WIRELESS CO PROBE / INSTALLATION AND OPERATION MANUAL 3.2.1 VENTILATION SPEEDS AND MODES. The ventilation system operates in one of the following modes. In each of these modes, the control device adjusts the ventilation system to a configured ventilation level. ABSENCE MODE: It represents periods of non-occupancy, when the heat recovery unit will operate at the lowest capacity. -
Page 7: Visual Signals
3.3 VISUAL SIGNALS LED STATUS LED MODES Start-up STEADY WHITE System status STEADY GREEN <800 PPM 800-1900 ppm STEADY YELLOW >1900 ppm 1 flash Communication error 2 flashes Dirty filter STEADY 3 flashes Fan error 4 flashes sensor error 5 flashes Low battery Selection ·... -
Page 8: Installation
DAITSU WIRELESS CO PROBE / INSTALLATION AND OPERATION MANUAL 5 INSTALLATION 5.1 PREPARATION DANGER NOTE Disconnect the power supply to the supply line, Do not place the device in a metal housing. circuit breaker or fuse before installing the de- vice. -
Page 9: Start-Up
5.3 START-UP 1. Enable the 230 V power supply. All of the LEDs will light up for 3 seconds. 2. Wait until the status LED displays link mode. If the device shows another indication, the device is already linked. See 6.2 on how to link the device again. 3. -
Page 10: Technical Data
DAITSU WIRELESS CO PROBE / INSTALLATION AND OPERATION MANUAL 7 TECHNICAL DATA DAITSU WIRELESS CO PROBE TOTAL DIMENSIONS 100 x 100 x 25 mm (height x width x depth) WEIGHT ± 125g Operating 0 to 40°C Temperature Transport -20 to 55° and storage ENVIRONMENTAL CONDITIONS... - Page 11 Eurofred S.A. Marqués de Sentmenat 97 08029 Barcelona www.eurofred.es I 11 DAITSU WIRELESS CO PROBE RHR-SCO2...