Page 1
PRODUCT MEETS INDUSTRY STANDARDS RECOGNIZED BY PARTICIPATING MEMBER Instruction Manual PLATFORM 2-MAN LADDER STAND MODEL #: PL201GW STYLE #: 161727 Maximum Height 18’ to Shooting Rail Maximum Field Rating 500 lbs Tree Diameter Range 12" to 20" Wear Your Harness!
Instruction Manual : PLATFORM 2-MAN LADDER STAND TABLE OF CONTENTS PAGE Warranty Information ..........................................2 Warnings ..............................................3-4 Parts List ..............................................5-9 Tools Required ............................................9 Hardware ..............................................9-12 Product Diagram............................................13 Finished Ladder ............................................14 Assembly Instructions ........................................15-21 Installation and Use Instructions ....................................22-25 Inspections and Maintenance ......................................26 Notes ................................................27 Note: Before beginning assembly of product, make sure all parts are present.
Instruction Manual : PLATFORM 2-MAN LADDER STAND READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE ASSEMBLY STOP MODEL PL201GW WARNING MAXIMUM USE HEIGHT - 18’ TO SHOOTING RAIL Never jump or bounce on a treestand to seat it to the tree.
Page 4
Instruction Manual : PLATFORM 2-MAN LADDER STAND WARNING Always lean forward as you climb and attach your harness to the tree before securing the platform to the tree and stepping onto the platform. Never exceed the stated maximum use height. Do Not use this product until you have watched the safety video, understand it, and practiced the techniques for safe hunting discussed in this video.
Instruction Manual : PLATFORM 2-MAN LADDER STAND PARTS LIST Item Part No. Image Description STABILIZER BAR # 33142 EXTENSION BRACE PLATFORM # 34243 ANGLED BRACE PLATFORM # 34244 TO LADDER BOTTOM LADDER # 34257 SECTION MIDDLE LADDER # 34258 SECTION TOP LADDER # 34259 SECTION...
Page 6
Instruction Manual : PLATFORM 2-MAN LADDER STAND Item Part No. Image Description SIDE SEAT # 34262 SUPPORT LEFT SIDE SEAT # 34263 SUPPORT RIGHT # 34264 SHOOTING RAIL SHOOTING RAIL # 34265 INSERT # 34268 BACKREST...
Page 7
Instruction Manual : PLATFORM 2-MAN LADDER STAND Item Part No. Image Description # 34269 SEAT SUPPORT # 34273 STABILIZER BAR BOTTOM TREE # 34274 BLADE # 34275 PLATFORM # 34297 FOOTREST # 34300 TOP TREE BLADE # 34363 SEAT...
Page 8
Instruction Manual : PLATFORM 2-MAN LADDER STAND Item Part No. Image Description MIDDLE LADDER # 34462 SECTION SHELF WITH # 34474 HOOKS FOAM SLEEVE # 34267 9 INCH FOAM PAD # 36284 ADHESIVE BACKED FOAM SLEEVE # 34266 36 INCH # 10531 HARNESS...
Instruction Manual : PLATFORM 2-MAN LADDER STAND Item Part No. Image Description RATCHET STRAP # 48415 WITH S HOOKS # MK034- 16’ CRISS-CROSS 4511 STRAP # MK021- 6’ CAM BUCKLE 1401 STRAP TOOLS REQUIRED (INCLUDED) # 32563 7/16” WRENCHES HARDWARE LIST (TO SCALE) Item Part No.
Page 10
Instruction Manual : PLATFORM 2-MAN LADDER STAND HARDWARE LIST (TO SCALE) Item Part No. Image Description BOLT 1/4-20 X # 48240B 1-1/2 IN BOLT 1/4-20 X # 48250B 1-3/4 IN BOLT 1/4-20 X # 48270B 2-1/2 IN BOLT 1/4-20 X # 48271B 2-1/4 IN # 48280B...
Page 11
Instruction Manual : PLATFORM 2-MAN LADDER STAND Item Part No. Image Description # 48752B NUT 1/4-20 RUBBER BUMPER # 48679 STOP # 48042B WING NUT 1/4-20 KNOB M6 X # 23604 10 MM KNOB M6 X # 28839 29 MM SQUARE PLUG # 29712 22 MM...
Page 12
Instruction Manual : PLATFORM 2-MAN LADDER STAND Item Part No. Image Description SQUARE PLUG # 29713 19 MM...
Instruction Manual : PLATFORM 2-MAN LADDER STAND FINISHED LADDER ASSEMBLED PLATFORM RATCHET STRAPS SECTION TOP LADDER SECTION CRISS-CROSS STRAPS MIDDLE LADDER SECTION STABILIZER BAR CAM STRAP MIDDLE LADDER SECTION WITH STABILIZER SLOT STABILIZER BAR BOTTOM LADDER SECTION All assembly must be done in the order on the following page at ground level before uprighting.
Instruction Manual : PLATFORM 2-MAN LADDER STAND ASSEMBLY INSTRUCTIONS Do not tighten any nut and bolt combinations completely until all parts are assembled together! Finger tighten plus one turn of a wrench only! This will temporarily hold the locknut on the bolt while helping alignment of all parts! After all parts are assembled together, all nut and bolt combinations must be completely tightened.
Page 16
Instruction Manual : PLATFORM 2-MAN LADDER STAND STEP 3 3. Attach left (8) and right (9) seat supports to platform sections (16) using four 1/4-20 x 2-1/2 IN bolts (34) and locknuts (41). SEE FIGURE 3. Attach platform braces (2) to platform section (16) and both left (8) and right (9) seat supports using four 1/4-20 x 1-1/2 IN bolts (32) and locknuts (41).
Page 17
Instruction Manual : PLATFORM 2-MAN LADDER STAND STEP 5 5. Secure rear of the seat assembly (19) to left (8) and right (9) seat supports using two 1/4-20 x 2-3/4 IN bolts (37), four orange plastic washers (40), two plastic spacers (38) and locknuts (41). SEE FIGURE NOTE: Be sure hardware is oriented as shown in FIGURE 5.
Page 18
Instruction Manual : PLATFORM 2-MAN LADDER STAND STEP 7 Slide top tree blade (18) through sleeve on rear of seat assembly (19) so that top tree blade is centered on hole in seat assembly (19). Install top tree blade (18) into brackets on ends of seat support (13) and secure using four 1/4-20 x 1-3/4 IN bolts (33) and locknuts (41).
Page 19
Instruction Manual : PLATFORM 2-MAN LADDER STAND STEP 9 Install M6 x 29 MM knobs (45) and M6 x 20 MM bolt (30) onto left (8) and right (9) seat supports. SEE FIGURE 9. Attach shooting rail assembly (11 and 17) to backrest (12) using two M6 x 70 MM bolts (31), plastic spacers (38) and M6 x 10 MM knobs (44).
Page 20
Instruction Manual : PLATFORM 2-MAN LADDER STAND STEP 11 11. Attach one end of brace supports (3) to J-tubes (7) underneath platform using two 1/4-20 x 1-1/2 IN bolts (32) and locknuts (41). SEE FIGURE 11. Slide top ladder section (6) into J-tubes (7) and secure using two 1/40-20 x 1-3/4 IN bolts (33) and locknuts (41).
Page 21
Instruction Manual : PLATFORM 2-MAN LADDER STAND STEP 13 13. Attach the stabilizer bar extension tube (1) to the middle ladder section (5) through the mounting bracket with one 1/4-20 X 1-1/2 IN bolts (32) and one 1/4-20 nut (41). SEE FIGURE 13. Slide the stabilizer bar (14) into the extension tube (1) and attach the two pieces together using one 1/4-20 X 1-1/2 IN bolt (32) and one wing nut (43).
Page 22
Instruction Manual : PLATFORM 2-MAN LADDER STAND READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE SETUP AND USE STOP WARNING WARNING Always maintain three (3) points of contact when Double check assembly steps to be certain you have correctly assembled this product. climbing a ladder treestand.
Instruction Manual : PLATFORM 2-MAN LADDER STAND INSTALLATION AND USE INSTRUCTIONS WARNING During installation and removal of ladder treestands, you must always and properly use the included Full Body Harness (Fall Arrest System). Refer to the Full Body Harness instructions Never use a treestand on a dead, leaning, diseased or included with this product for proper use.
Page 24
Instruction Manual : PLATFORM 2-MAN LADDER STAND STEP 3 4. a. Loop the D-loop end of the two 16’ criss cross straps (27) through the loop end to form a cinch knot around the ladder rail tube. Secure beneath a step rung, at the stabilizer bar height location.
Page 25
Instruction Manual : PLATFORM 2-MAN LADDER STAND STEP 4 7a. Standing on ladder step, lean toward tree with ratchet strap (26) now in hand, hook “S” hook with long strap through hole provided on bottom tree blade. Feed the long strap through the center (slot) of ratcheting mechanism and back around through tightening lever.
Instruction Manual : PLATFORM 2-MAN LADDER STAND INSPECTION AND MAINTENANCE BEFORE EACH USE PERFORM THE FOLLOWING: • Inspect all webbing, rope, cord, and strap assemblies for wear or damage. • Inspect cables and/or cable ends for damage or kinking. • Inspect all hardware and chain components for damage or wear.
Instruction Manual : PLATFORM 2-MAN LADDER STAND NOTES...
Page 28
*All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images may have been removed for photography purposes only. Props shown in photos not included. Some assembly may be required.