Beltronics LaserPro 905 User Manual

1 Y E A R LIMITED WA RRAN T Y
BELTRONICS warranties your LP905 against all defects in materials and workmanship for a
period of one (1) year from the date of the original purchase, subject to the following terms and
conditions:
The sole responsibility of BELTRONICS under this Warranty is limited to either repair or, at the
option of BELTRONICS, replacement of the LP905. There are no expressed or implied warranties,
including those of fitness for a particular purpose or merchantability, which extend beyond the
face hereof.
Some states do not allow limitations on how long an implied warranty lasts, so the above
limitations may not apply to you.
BELTRONICS is not liable for any incidental or consequential damages arising from the use,
misuse,
or mounting of the LP905. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This Warranty gives you specific rights. You may have other legal rights which vary from state to
state. This Warranty does not apply if the serial number on the housing of the 5-port interface has
been subjected to physical abuse, improper installation, or modification.
5442 West Chester Road, West Chester, Ohio USA 4 5 0 6 9
Customer Service: 800-341-2288 USA • 800-268-3994 CAN
w w w. b e l t r o n i c s p r o . c o m
121L905-0 Printed in Canada
L a s e r P ro 905
The o p e rates in conjunction with select BEL Pro radar detectors.
L a s e r P ro 905
This unique configuration of the
P ro radar detector, c reates the most comprehensive radar/laser protection possible.
L a s e r P ro 905
o p e rates with your BEL detector using the " l i n k "cable prov i d e d .
L a s e r P ro 905
When the is connected to your BEL Pro dash model radar detector,
all visual and audible alerts will be generated through the detector's display.
S t a rt Up Sequence
Once the LaserPro 905 is installed, your BEL Pro dash mounted detector will
p rovide confirmation of correct installation by display i ng "
d e f a u l t ) . This message confirms that the three laser sensors are re a dy to " B l o c k "
all laser signals encountere d .
L a s e r P ro 905
Accessing
Once your BEL detector is connected to the
Laser Blocker's operate in pro g ramming:
L P 9 0 5Bl k
1 . – all laser sensors are set to " B l o c k "incoming laser signals,
p roviding true laser countermeasure s .
L P 9 0 5 Re c
2 . – all laser sensors are in " receive only"m o d e , p roviding laser
detection without any " B l o c k i n g " .
L P 9 0 5 Off
3 . – all laser sensors are " O F F " . In this mode, no laser signals will
be detected or " B l o c k e d " .
To access the above features through your BEL PRO radar detector:
1 . P ress and hold the CITY and BRT buttons for 2 seconds. The unit will sound
P r o g r a m
t wo " b e e p s "and display the wo rd ,"
2 . P ress the CITY/REV button until you reach the LP905 category.
(NOTE: This option is only visible when the LP905 is connected and
working properly).
3 . P ress the CHG/BRT button to toggle between the three selections:
L P 9 0 5Bl k
( f a c t o ry default once the LP905 is connected)
L P 9 0 5 Re c
L P 9 0 5 Off
To exit pro g ra mming mode, wait 8 seconds without pressing any buttons or
Co m p l e t e
p ress PWR. The unit will display "
to normal opera t i o n .
laser countermeasure s , and a BEL
L P 9 0 5 Blk
"( f a c t o ry
s e t t i n g s
L a s e r P ro 905
, you can select how the
" .
,"emit sev e ral " b e e p s "and return