Table of Contents
Advertisement
Available languages
Available languages
ENGLISH
1
Battery cartridge
2
Set plate
3
Charging light
4
Fast charger
5
Switch trigger
6
Hex socket head bolt M6 x 16
7
Flat washer 6
8
Cutter head
SPECIFICATIONS
Model
Cutting capacities
Mild steel ................................................ M8, M10, M12
Cutting speed ................................................2.5 seconds
Overall length ...................................................... 316 mm
Net weight ................................................................. 4 kg
Rated voltage ....................................................D.C. 12 V
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1.
SAVE THESE INSTRUCTIONS — This manual
contains
important
instructions for battery charger.
2.
Before
using
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product using
battery.
3.
CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4.
Do not expose charger to rain or snow.
5.
Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to
persons.
6.
To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when
disconnecting charger.
7.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8.
Do not operate charger with damaged cord or
plug — replace them immediately.
9.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
10. Do not disassemble charger or battery cartridge;
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
Explanation of general view
9
Blade A
10 Blade B
11 Cutter rod
12 Loosen
13 Tighten
14 Screwdriver
15 Stopper
16 Claw of stopper
SC120DA
safety
and
operating
battery
charger,
read
11. To reduce risk of electric shock, unplug charger
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
12. The battery charger is not intended for use by
young children or infirm persons without
supervision.
13. Young children should be supervised to ensure
that they do not play with the battery charger.
14. If operating time has become excessively
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
15. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY CARTRIDGE
1.
Do
not
ENC001-3
temperature is BELOW 10°C (50°F) or ABOVE
40°C (104°F).
2.
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
all
3.
Do not allow anything to cover or clog the
charger vents.
4.
Always cover the battery terminals with the
battery cover when the battery cartridge is not
used.
5.
Do not short the battery cartridge:
(1) Do not touch
conductive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating,
breakdown.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7.
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8.
Be careful not to drop, shake or strike battery.
9.
Do not charge inside a box or container of any
kind. The battery must be placed in a well
ventilated area during charging.
17 Spring
18 Stopper securing bolt
19 Threaded rod
20 X direction
21 Y direction
22 M8 or M10
23 M12
24 Hex bolt
charge
Battery
Cartridge
the terminals with any
possible
burns
when
and
even
a
5
Advertisement
Table of Contents
