Table of Contents Precautions ..........3 About This Manual ........3 Names and Functions of Parts and Controls ..........4 Installation ..........5 Playback of Still Images or Video From a CF Card ..........6 Compatible media and file formats ....6 Inserting a CF card ........
• The software specifications of this unit This manual describes use and operation of are subject to change for improvements the BKM-FW50 as installed in a Flat Panel without notice. Display of the FWD series and connected • Screens shown by application software to a network.
Names and Functions of Parts and Controls 1 USB port 6 Memory card slot The port will be used for expanded Accepts a CF card. functions to be introduced in future. 7 RESET button 2 Memory card slot cover fastening When this button is pressed and held for screw more than 3 seconds, all settings of the unit...
AC outlet. • While carrying out the installation, the display must be firmly secured. Install the BKM-FW50 inside the display as follows. If an optional adaptor is installed, loosen its fastening screws (top and...
CompactFlash cards (not supplied). If you insert a CF card that contains images shot with a digital still camera into the slot of the BKM-FW50, the images can be viewed on the display in a slide show format. You can make various settings for playback of still images or video.
Functions into the BKM-FW50, JPEG format still image files will be automatically detected, and the images will be shown on the The BKM-FW50 can be connected to a display as a slide show. network with 10BASE-T/100BASE-TX LAN cable. Detailed control of playback...
4) Make settings for the other items automatically by a DHCP server on the in the same way. network. Use the M/m buttons to select Connect the BKM-FW50 installed in “Execute” and press the ENTER the display to the network, using button. suitable LAN cable.
ENTER button. The “INITIAL You can make various display settings on the screen of the computer. SETUP/INFORMATION” menu Make sure that the BKM-FW50 is properly appears. installed in the display, and that the BKM- FW50, computer, and router or hub are Use the M/m buttons to select “IP...
Page 10
Contrast +/– buttons Configure screen Adjust the screen contrast. Timer Brightness +/– buttons Lets you make settings for the timer Adjust the screen brightness. function. Click “Apply” when done. Chroma +/– buttons Adjust the color intensity. Screen Saver Lets you make settings for the screen saver Phase +/–...
Page 11
Web/HTTP server. HTTP server and save them on a CF card (not supplied) inserted in the memory card Server Address slot of the BKM-FW50. Enter the IP address of the Web/HTTP server where the still image or video files Server Address are stored.
Page 12
UltraVNC is included on the CD-ROM The “DCIM\101MSDCF” folder is set as supplied with the BKM-FW50. Insert the the factory default. CD-ROM into the CD-ROM drive of the computer and follow the on-screen Repeat instructions to install UltraVNC.
Page 13
Only Select this to disable the PC Presentation music files stored on a CF card inserted function. in the BKM-FW50 can be used for this function. When the “Check to use background Play Settings music during video playback (video audio will be muted)”...
Page 14
DHCP server. In this case, be aware connecting to the SMTP server, select that the IP address will change each time this check box. the display attached to the BKM-FW50 is Ingoing Mail Server (POP3): turned on. When POP authentication is used for Note the “POP before SMTP”...
Page 15
For information about supported ID Talk commands, contact your local Sony dealer. SNMP The BKM-FW50 is a network device which supports SNMP (Simple Network Management Protocol). Besides standard MIB-II, Sony Enterprise MIB is also supported. This screen allows making settings for SNMP.
Cause/Remedy • BKM-FW50 is not correctly installed in Cannot connect to network. display. t Push the BKM-FW50 fully into the slot, and tighten the fastening screws. • Cable is not connected correctly to network port. t Plug the cable firmly into the network port.
(10.6 oz.) Power consumption Approx. 10 W Operating temperature 0 to +35°C (+32 to +95°F) (environment conditions for display in which BKM-FW50 is installed) Storage temperature –10 to +40°C (+14 to +104°F) LED indicators Link (green)/ Act (orange) Cable length Max.