Related Manuals for FEC AM-1017
Summary of Contents for FEC AM-1017
- Page 1 System Manual Model Name: AM-1017 Document Version: I Customer Date Prepared by Date _________ Checked & Approved by Approved by...
- Page 2 System Manual Aer Monitor User's Manual Version-0.2...
- Page 3 System Manual Copyright Notice This document is copyrighted, 2013. All rights are reserved. Firich Enterprise Co., Ltd reserves © the right to make improvements of the product described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission from Firich Enterprise Co., Ltd.
- Page 4 System Manual Safety and Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4.
-
Page 5: Table Of Contents
Touch Display Installation & Swapping ..............10 OSD Function and Adjustment ................... 11 Chapter 3 Software Installation and Setup FEC P-Capacitive/ Resistive Touch Utility (EETI Controller) ..........12 EETI TouchKit Tools Installation ..................13 TouchKit Control Panel for P-Capacitive/ Resistive Touch ..........16 Chapter 4 Specifications AM-1017 Specifications .................... -
Page 6: Introduction
AerMonitor is a 17 inch bezel free monitor which is slim, compact, and yet tough enough for any environment. With easy accessed on screen display controls, users can adjust brightness and display is a compatible component and can be easily removed and installed on the FEC AerPOS Terminal Series. - Page 7 System Manual AM-1017...
-
Page 8: A Quick Tour For Am-1017
System Manual A Quick Tour for AM-1017... - Page 9 System Manual 17” Touch Display Display OSD Power Switch / Status Blue LED: Power ON Red LED: Power Off / Standby Menu item up select, item value increase and auto tune Display OSD Menu item down select and item value decrease Display OSD menu and enter Next page Note: All buttons are invisible till one touch of any.
-
Page 10: Am-1017 Dimension
System Manual AM-1017 Dimension... - Page 11 System Manual H: 382mm W: 409.9mm D: 212.3mm...
-
Page 12: Rear I/O Panel Connectivity
Connect speakers to this port Connector Aer Monitor AM-1017 Packing List Standard Optional & Peripherals 17” AM-1017 Aer Monitor Touch Terminal MSR / RFID / Finger Print Receiver I-Button 50W (12V/4.16A) External Power Adaptor 2 20x2 VFD / 20x2 LCM / 240x64 LCM 15”... -
Page 13: Msr / Finger Print Reader/ Rfid / I-Button Installation
Type Connector. Fix the Touch Display Module with one screw. 3. Make sure the USB connected and screw is fastened well. 4. If you are looking for the detail Utility of MCR, Finger Print Reader, I-button Reader, RFID Reader, please contact FEC’s FAE. -
Page 14: 15" 2 Nd Pole Type Vfd / Lcm Installation
System Manual 15” 2 Pole Type VFD / LCM Installation Assemble the 2 screen with pole type with 2 screws Assemble the 2 Screen with pole type to Terminal. Plug in VGA and DC 12V cables Note : They should connect to the system. -
Page 15: 17" 1 St Touch Display Installation & Swapping
System Manual 17” 1 Touch Display Installation & Swapping Release 2 thumb screw at the back side of Display Lift the Display Module up to disassemble from the main unit of terminal Display and Aer monitor base are separated. -
Page 16: Osd Function And Adjustment
System Manual Reverse the process can assembly back the touch display module. ** please make sure the touch display module is firmly connected to the docking slot **Note** During the process of disassembly and installation, please ensure the terminal is “Power Off”... -
Page 17: Software Installation And Setup
11)EXIT exit OSD menu Software Installation and Setup AM-1017omes with a variety of drivers for different operating systems. You can download all the necessary drivers and utilities from http://www.fecpos.com. FEC P-Capacitive/ Resistive Touch Utility (EETI Controller) -
Page 18: Eeti Touchkit Tools Installation
System Manual FEC Projective – Capacitive Touch Utility Introduces: 1. Mode of FEC Capacitive Touch Panel and default settings 2. EETI TouchKit Tools Installation Mode of FEC P-Capacitive/ Resistive Touch Panel Win XP, POS Ready 2009 Win7, POS Ready7 Mouse Mode... - Page 19 System Manual Click Next and do not choose RS232 Select None...
- Page 20 System Manual Click Next for further installation process Select No...
-
Page 21: Touchkit Control Panel For P-Capacitive/ Resistive Touch
System Manual TouchKit Control Panel for P-Capacitive/ Resistive Touch This section explains the different options in the TouchKit control Panel. Tools tab P-Capacitive Resistive Do not need to calibrate the touch screen with the The tools tab allows you to below calibrate 4 Points. -
Page 22: Specifications
System Manual Specifications AM-1017 Specifications Aer Monitor AM-1017 Stand Type 17’TFT LCD LCD Display Size Max. Resolution 1280 x 1024 Max. Color 16.7 M Contrast Ratio 1000: 1 Main Touch Touch Screen Specifications Projective-Capacitive 5W Resistive Panel Brightness 350 nits... - Page 23 PLUG / Power12V USB Others 409.9 x 331.8 x 38.6 (Without Base) 409.9 x 382 x 212.3 Dimension (With Base) Mounting VESA 100 x 100 Aer Monitor AM-1017 Bracket Type 17’’TFT LCD LCD Display Size Max.Resolution 1024 x768 Max.Color 16.2 M Contrast Ratio...
-
Page 24: Troubleshooting
System Manual Troubleshooting Please note that the following troubleshooting guide is designed for people with strong computer hardware knowledge or Engineers and Maintenance. Touch Panel Does Not Work Check “Touch Display Module” is connected well with terminal. Check HID USB touch device is detected by OS. (Resistive Touch) Check if the EETI driver or the TouchKit driver has been properly installed.