Related Manuals for FEC AM-1008W
Summary of Contents for FEC AM-1008W
- Page 1 Manual Model Name: AM-1008W (8”) Document Version: V1.1 Customer Date Prepared by Date _________ Checked & Approved by Approved by Page 1 of 21...
- Page 2 Manual Record of Revision: Date Specs Description Note Ver. 2016.07.31 V0.1 Initial Draft Cary 2016.09.30 V0.2 Add Specs Cary 2016.10.30 V0.3 Add Customer Display Cary 2017.01.19 V0.4 Add Setup Instructions, Revised NFC & Cary Customer Display Section 2017.02.11 V1.0 First Release Cary 2017.06.20 V1.1...
- Page 3 Manual Safety and Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect from power outlet before cleaning, disassembly or transport. Do not use liquid or spray detergents for cleaning. Use a damp cloth only and avoid any prolonged contact with moisture.
- Page 4 Manual personnel: The power cord, plug, or adapter is visibly damaged. Liquid has entered into the equipment. The equipment has been exposed to moisture. The equipment does not work as intended, or you cannot get it to work according to the user’s manual.
-
Page 5: Table Of Contents
Manual Contents Chapter 1 – Introduction About AM-1008W Overview I/O Layout Package Contents Chapter 2 – Hardware & Software Standalone Setup Connecting to System Customer Display Option NFC Option Chapter 3 – Specifications Appendix A – Customer Display Command List... -
Page 6: Chapter 1 - Introduction
Manual Chapter 1 – Introduction About AM-1008W AM-1008W is a new type of multifunction LCD display. Featuring 8” widescreen LCD panel with bright LED backlight, slim frame and innovative features. Main Features: All in one compact design with integrated and standalone mounting options. -
Page 7: Overview
Integrated Mount Wallmount I/O Layout AM-1008W features an unique all-in-one connection allowing simple setup and cable management. A custom-designed connector houses both video and power supply. Depending on the SKU ordered, your cable may look different from the illustrations below. - Page 8 Manual Standard Optional Items AM-1008W Main Display Unit AerARM with Bracket Integrated Cable Extension tubes, standalone base Wallmount Kit Page 8 of 21...
-
Page 9: Chapter 2 - Hardware & Software
Do not perform any service or upgrade without shutting down the terminal first. Power must be switched off and power cord must be unplugged. Failure to do so may result in system damage which is not covered by FEC warranty. Standalone Setup 1. Unpack the contents 2. - Page 10 Manual CLICK! 3. Unwrap the cable from its protective bag and untie the cable tie to loosen the cables. Page 10 of 21...
- Page 11 Manual 4. Starting with the thinnest cable (USB or RS232, thread it through the base opening as shown. 5. Keeping the threaded cable to the left side, thread the video signal cable (HDMI or VGA) through as shown. Page 11 of 21...
- Page 12 Manual 6. Align the extension tubes with docking socket facing the narrow side of the base, pull the cables through and assemble the extension tubing to the base using the method outlined in Step 2. Page 12 of 21...
- Page 13 Manual CLICK! 7. Tilt the stand over and thread the cables as shown (thinnest cable always first) Page 13 of 21...
- Page 14 Manual 8. Dock the screen as shown by aligning the points circled and push the screen downward to dock with the stand. 9. Lay the unit face down and attach the two screws as shown. Page 14 of 21...
- Page 15 Manual 10. Assembly is now complete. Page 15 of 21...
-
Page 16: Connecting To System
3. If nothing is displayed, first check your system is configured properly, then disconnect the cabled and repeat Step 1 & 2 again. Customer Display Option AM-1008W can emulate 20x2 VFD compatible with EPSON commands. The output is displayed using overlay technology. COM Port Settings... -
Page 17: Nfc Option
1. The NFC module is configured to be HID USB read only by default. To enable Virtual COM read/write mode, please install the Virtual COM driver provided by FEC. 2. If the driver is not included, please contact your FEC representative. Chapter 3 – Specifications Page 17 of 21... -
Page 18: Appendix A - Customer Display Command List
Manual *specifications are subject to change without notice. Contact your nearest FEC representative for latest information. Appendix A – Customer Display Command List Command Function Description Move cursor right Move cursor left 1F 0A Move cursor up Move cursor down... - Page 19 Manual Select/cancel cursor display 1F 43 n n=0, canceled ; n=1, selected Clear display screen Clear cursor line Brightness adjustment 1F 58 n 1≦n≦4 Blink display screen 0≦n≦255 (n*50msec) ON / (n*50msec) OFF 1F 45 n n= 0, blinking is canceled n=255, display is turned off 1B 40 Initialize display...
- Page 20 Manual 1A 1B Enter Burn In Test Mode 1A 1C Break Burn In test mode 1A 1E Exit Burn In test mode 1A 01 Display Monitor Model Edit Monitor model name 1A 02 0D n = 1 ~ 16 bytes Power Saving mode 1A 03 n 0D n = 0, power saving mode off;...
- Page 21 Manual 1E 21 Full Screen : White color 1E 22 Full Screen : Red color 1E 23 Full Screen : Blue color 1E 24 Full Screen : Green color 1E 25 Full Screen : Black color 1E 26 Cancel R , G , B Color 1E 2D Display Resolution and Frequency 1E 30...