Using An Extension Cable; Assembly And Adjustments - DeWalt DWD112 Instruction Manual

WARNING: NEVER use a light socket.
NEVER connect the live (L) or
neutral (N) wires to the earth
pin marked E or

Using an extension cable

An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm ; the maximum length is 30 m.
2
Also refer to the table below.
Conductor size (mm )
2
0.75
1.00
1.50
2.50
4.00
Cable length (m)
7.5
Voltage Amperes Cable rating (Amperes)
115 0 – 2.0 6
2.1 – 3.4 6
3.5 – 5.0 6
5.1 – 7.0 10
7.1 – 12.0 15
12.1 – 20.0 20
230 0 – 2.0 6
2.1 – 3.4 6
3.5 – 5.0 6
5.1 – 7.0 10
7.1 – 12.0 15
12.1 – 20.0 20
When using a cable reel, always unwind the cable
completely.

assembly anD aDjUsTmenTs

WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
.
Cable rating (Amperes)
6
10
15
20
25
15 25 30 45 60
6 6 6 6 10
6 6 6 6 15
6 10 15 20 20
10 15 20 20 25
15 20 25 25 –
20 25 – – –
6 6 6 6 6
6 6 6 6 6
6 6 6 10 15
10 10 10 15 15
15 15 15 20 20
20 20 20 25 –
OPeraTiOn
instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
switches (fig. 1, 2)
To start the drill, depress the trigger switch; to stop
the drill, release the trigger.
A variable speed trigger switch (a) permits speed
control—the farther the trigger is depressed, the
higher the speed of the drill.
For continuous operation, press and hold the
variable speed switch, move the lock-on button (b)
up, then release the switch.
NOTE: Use lower speeds for starting holes without
a center punch, drilling in metal or plastics, driving
screws or drilling ceramics. Higher speeds are better
for drilling wood and composition boards and using
abrasive and polishing accessories.
The forward/reverse lever (c) is used for withdrawing
bits from tight holes and removing screws. It is
located above the trigger switch. To reverse the
motor, release the trigger switch FIRST and then
push the lever to the right. After any reversing
operations, return lever to forward position.
To stop continuous operation, press the switch
briefly and release it. Always switch the tool off when
work is finished and before unplugging.
Drilling
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
"back-up" block to prevent damage to
the material.
1. Use sharp drill bits only. For WOOD, use twist
drill bits, spade bits, power auger bits, or hole
saws. For METAL, use steel twist drill bits or
hole saws.
2. Always apply pressure in a straight line with the
bit. Use enough pressure to keep drill biting, but
do not push hard enough to stall the motor or
deflect the bit.
3. Hold tool firmly with both hands to control the
twisting action of the drill.
4. IF DRILL STaLLS, it is usually because
it is being overloaded or improperly used.
RELEaSE TRIGGER IMMEDIaTELY, remove
drill bit from work, and determine cause of
stalling. DO NOT CLICK TRIGGER ON
e ngl ish
23