First Use /Active / Passive - Manner; Setting The Time; Filtering And Cleaning - Sanotechnik SanoSpa SPA08 Instructions For Using Manual

When first turning on the power, the backlight will bright of halt, and the LCD will show the
When first turning on the power, the backlight will bright of halt, and the LCD will show the
present time and temperature. It will show "E1" if the sensor is open/short circuit. When part
present time and temperature. It will show "E1" if the sensor is open/short circuit. When part
of radio frequency showed "---", it indicates that the status of the system is "Waitting Mode",
of radio frequency showed "---", it indicates that the status of the system is "Waitting Mode",
so as well as the pre-heat and circulation cleaning.
so as well as the pre-heat and circulation cleaning.
active manner
active manner
The lock will start work by pressing
The lock will start work by pressing "
The lock will start work by pressing "
operation lasting above 30 minute. In the status of Locked, press the button
pressing operation lasting above 30 minute. In the status of Locked, press the button
pressing operation lasting above 30 minute. In the status of Locked, press the button
will be unlocked, and the word "LOCKED" will disappear.
" " twice, the lock will be unlocked, and the word "LOCKED" will disappear.
" " twice, the lock will be unlocked, and the word "LOCKED" will disappear.
C.

SETTING THE TIME

In the status of "Waitting Mode" and the pre-heater and circulation cleaning are shut down,
pressing or
48 flash at this time. It will add 1 hour when pressing
continually when pressing the
of time setting, It will add 1 minute when pressing
continually when pressing the
0~59. The system will quit the time-setting status automatically after 6 seconds without pressing.
D.

FILTERING AND CLEANING

You have the option to set ones a day filtering in the pool, but it can also be all the time on. To set
a ones a day filtering then press
start time of the filtering.
Then press
MHz/CH
SET
The maximum filter time is 19 hours and 55 minutes! To exit settings, press
filter settings from being saved. However, if you press
When you have saved the settings a filtering sign appears on the screen.
When the clock you set for filtering appears, the circular pump turns on and the water cleaning
starts. It does not matter if the operation is in active or passive mode, the cleaning is switched on
in each case.
The screen shows the cleaning time, which is counting down. In the initial 30 seconds of cleaning
a jet massage pump is also active to purify the inlet and outlet pipes of the pool. In the first 59
seconds of cleaning, this procedure can not be interrupted. After 1 minute by pressing
can cancel filtering.
52 INSTRUCTION FOR USING THE SPA OUTDOORPOOL
B. FIRST USE /ACTIVE / PASSIVE - MANNER
When first turning on the power, the backlight will bright of halt, and th
present time and temperature. It will show "E1" if the sensor is open/sh
of radio frequency showed "---", it indicates that the status of the system
so as well as the pre-heat and circulation cleaning.
passive manner
The lock will start work by pressing "
pressing operation lasting above 30 minute. In the status of Lock
"
could start time setting. Signal of ":" doesn't flash but Minute and Hour
PROGRAMMING INSTRUCTIONS
PROGRAMMING INSTRUCTIONS
48
without stop. The hour adjustment range is 0~23. In the status
without stop. the minute adjustment range of the minute is:
3
CYCLE
. Now you can use the
passive manner
active manner
. Button in the status of "Waitting Mode"or no- pressing
"Button in the status of "Waitting Mode"or no-
"Button in the status of "Waitting Mode"or no-
" twice, the lock will be unlocked, and the word "LOCKED" w
each time, and the hours could be added
PROGRAMMING INSTRUCTIONS
each time, and the minutes could be added
in passive manner, then press
or button to set the duration of the filtering.
passive manner
or
3
CYCLE
, your filtering settings will be saved.
twice, the lock
"Button in the status of "
to set the
to prevent your
you