Remington Ultra Smooth Use & Care Manual page 4

Shaver Operation
To switch the shaver ON,press down on the Switch
Lock feature,and slide the On/Off Button toward the
top of the shaver.
To switch the shaver OFF, simply slide the On/Of f
Button towards the bottom of the shaver. (There is
no need to press on the Switch Lock feature.)
Charging
B e fore using your shaver for the first time, put it on charge
for 24 hours.
To charge your shaver:
Slide the power button downward to the "Off"
position.
Connect the AC power cord to the shaver and then to
the electric outlet. A green indicator light will come on.
Your shaver cannot be overcharged,so you can leave
it plugged in and charging between shaves.
Use only the AC line cord supplied with the shaver.
The ES-1000 comes with a special feature that
allows you to shave when the battery charge is low.
Just follow the steps above to connect the AC power
cord and turn on the shaver. Your shaver will not
charge while you are shaving,so after shaving,
turn off the shaver and leave it plugged in so it
can recharge.
Note: Your ES-1000 cord/cordless shaver should not
be used strictly as a cord-operated shaver, as continued
cord-only use will shorten the life of the battery.
Indicator Lights
Green - Lights up when the shaver is charging.
Red - Lights up if the battery is low. When it first
comes on,you have approximately 5 to 6 minutes
of shaving time left before the shaver must be
recharged.
Note: To preserve the life of the batteries,they should
be fully discharged every six months and then fully
charged for 24 hours.
Worldwide Voltage
You can take your ES-1000 shaver with you when you travel just
about anywhere in the world.The shaver features worldwide
automatic voltage conversion.
Battery Removal
When your rechargeable shaver reaches the end of its useful life,
the batteries must be removed from the shaver and be recycled
or disposed of properly in accordance with your state and local
requirements.
THE FOLLOWING PROCEDURE SHOULD BE
FOLLOWED FOR BATTERY REMOVAL:
Turn the shaver OFF, and unplug power
cord from electric outlet to avoid possible
electric shock hazard.
Remove Hairpocket and Head assembl y.
Unfasten the two screws located along
the top of the rear housing (see Fig.1).
Remove plate from top of the shaver
(see Fig. 2 ) .
Squeeze the front housing and pull it
aw ay from the rear housing to expose the
electrical board and batteries (see Fig.3).
Cut or break the metal tabs that connect the
batteries to the electrical board (see Fig.4).
Lift the batteries off (see Fig.4a).
Dispose batteries properly (see below).
CAUTION:DO NOT PUT BATTERIES IN FIRE OR MUTILATE THEM
WHEN DISPOSING AS THEY MAY BURST OR RELEASE TOXIC
MATERIALS.DO NOT SHORT CIRCUIT AS IT MAY CAUSE BURNS.
Fig. 1 DISPOSE PROPERLY IN ACCORDANCE WITH YOUR LOCAL AND
STATE REQUIREMENTS.
The EPA-certified RBRC ®
cadmium (Ni-Cd) battery indicates Remington Products Company,
L.L.C.is voluntarily participating in an industry program to collect
and recycle these batteries at the end of their useful life,when
taken out of service in the United States or Canada.The RBRC
Fig. 2
program provides a convenient alternative to placing used Ni-Cd
b atteries into the trash or the municipal waste stream, which
may be illegal in your area. Please call 800-8-BAT T E RY
i n fo r m ation on Ni-Cd bat t e ry recycling and disposal bans/restriction
in your area.Remington Products Company, L.L.C.'s involvement
in this program is part of our commitment to preserving our
e n v ironment and conserving our natural resources.
Fig. 3
Fig. 4
Fig. 4a
Battery Recycling Seal on the nickel-
®
S M for