Related Manuals for Halma Ocean Optics HL-2000-FHSA
Summary of Contents for Halma Ocean Optics HL-2000-FHSA
- Page 1 Halogen Light Source with Attenuator and TTL-Shutter Installation and Operation Manual For Products: HL-2000-FHSA / HL-2000-FHSA-LL / HL-2000-FHSA-HP Document: 000-10000-070-02-201504 000-00000-...
- Page 2 AMERICAS & WORLD HEADQUARTERS Ocean Optics, Inc. Phone: +1 727-733-2447 830 Douglas Ave. Fax: +1 727-733-3962 Dunedin, FL 34698 Sales: info@oceanoptics.com Orders: orders@oceanoptics.com Manufacturing & Logistics Support: techsupport@oceanoptics.com 4301 Metric Dr. Winter Park, FL 32792 EUROPE, MIDDLE EAST & AFRICA Sales &...
- Page 3 Important Safety Notices 1. Do not remove or modify any installed safety device on this equipment. Doing so will void your warranty and create an unsafe operating environment. 2. Dangerous voltages are present in this device. There are NO user serviceable parts inside. 3.
- Page 4 Important Safety Notices 000-10000-070-02-201504...
-
Page 5: Table Of Contents
Table of Contents About This Manual ......................iii Document Purpose and Intended Audience ................iii What’s New in this Document ....................iii Document Summary ........................iii Product-Related Documentation ....................iii Upgrades ..........................iii Chapter 1: Setup ................... 5 Overview ..........................5 Unpacking the HL-2000-FHSA ..................5 Contents ..........................6 Setting Up the HL-2000-FHSA Light Source ..............6 Enabling Automatic Shutter Control ...................7... - Page 6 Table of Contents 000-10000-070-02-201504...
-
Page 7: About This Manual
About This Manual Document Purpose and Intended Audience This document provides you with an installation section to get your system up and running. What’s New in this Document This version of the Halogen Light Source with Attenuator and TTL-Shutter HL-2000-FHSA / HL-2000- FHSA-LL / HL-2000-FHSA-HP Installation and Operation Manual updates logo and the contact information, and the bulb replacement instructions Document Summary... - Page 8 About This Manual 000-10000-070-02-201504...
-
Page 9: Chapter 1: Setup
Chapter 1 Setup Overview The following sections provide instructions on unpacking and setting up your HL-2000-FHSA Light Source. Before using the HL-2000-FHSA for the first time, check for transport damage. Be sure to adhere to all warnings on the unit and in this manual. Unpacking the HL-2000-FHSA ►... -
Page 10: Contents
2: HL-2000 Specifications 2. Inspect the outside of the instrument and make sure that there is no damage. Do not use the instrument if damage is present. Contact your dealer for repair or replacement information, if necessary. 3. Use this instrument in a clean laboratory environment. Contents Your HL-2000-FHSA package should contain the following: HL-2000 Light Source... -
Page 11: Enabling Automatic Shutter Control
2: HL-2000 Specifications HL-2000-FHSA Rear View 3. Connect the SMA connector of your fiber optic cable to the SMA plugs. HL-2000-FHSA Right Side View 4. Turn the Halogen lamp on using the power switch on the rear of the HL-2000-FHSA. HL-2000-FHSA Rear View Enabling Automatic Shutter Control The HL-2000-FHSA is equipped with a 15-pin TTL port on the rear of the unit that allows an external... -
Page 12: Optimizing The Optical Power Output
2: HL-2000 Specifications 1. Insert the supplied IC-DB-15-2 15 pin connector into the port on the rear of the HL-2000-FHSA. HL-2000-FHSA Rear View 2. Move the shutter switch on the rear of the unit into the appropriate position to select the shutter mode. -
Page 13: Attenuating The Optical Power Output
2: HL-2000 Specifications 3. Shift the SMA socket to optimize the optical power of the HL-2000-FHSA. 4. Tighten the blocking screw to secure the SMA socket position. Attenuating the Optical Power Output The HL-2000-FHSA allows you to attenuate the optical output of the unit by adjusting the attenuation screw. -
Page 14: Hl-2000-Fsha Diagrams
2: HL-2000 Specifications HL-2000-FSHA Diagrams Power Connector Power Supply HL-2000-FHSA Power Supply 000-10000-070-02-201504... - Page 15 2: HL-2000 Specifications HL-2000-FHSA Rear View Filter Holder Fixture Screw SMA Connector HL-2000-FHSA Side View 000-10000-070-02-201504...
- Page 16 2: HL-2000 Specifications HL-2000-FHSA Bottom View Note Do not completely remove the bulb fixture screw. It may be hard to reinsert it. 000-10000-070-02-201504...
-
Page 17: Chapter 2: Hl-2000-Fhsa Specifications
2: HL-2000 Specifications Chapter 2 HL-2000-FHSA Specifications This section provides information on the operating environment, physical controls, and dimensions of the HL-2000-FHSA, as well as pinouts for the DB-15 connector. It also provides a parts list. Specifications HL-2000-FHSA HL-2000-FHSA-LL HL-2000-FHSA-HP 360 nm –... -
Page 18: Pinout Information
2: HL-2000 Specifications Pinout Information The following table contains pinout information for the HL-2000-FHSA Light Source: Description Ground TTL Signal – Shutter control na = not applicable 000-10000-070-02-201504... -
Page 19: Pinout Diagram
2: HL-2000 Specifications Pinout Diagram Parts List Spare Parts / Order Information Catalog Number Halogen light source with filter holder/shutter and attenuator HL-2000-FHSA Halogen light source, fan cooled, long life HL-2000-FHSA-LL Halogen light source High-Power with Attenuator and TTL-Shutter HL-2000-FHSA-HP Halogen spare bulb 2.960K/ 1.500 hrs HL-2000-B Halogen spare bulb 2.800K / 10.000 hrs... - Page 20 2: HL-2000 Specifications 000-10000-070-02-201504...
-
Page 21: Appendix A: Bulb Replacement
Appendix A Bulb Replacement Overview To order replacement bulbs for the HL-2000-FHSA, consult the Parts List. WARNING Before replacing the bulb in the HL-2000-FHSA, disconnect the lamp from your power source and allow the unit to cool for at least twenty minutes, if necessary. Replacing the Bulb ►... - Page 22 A: Bulb Replacement 6. Disconnect the wires from the connection block. 7. Replace the bulb and reconnect the wires to the connection block. 8. Slide the lamp into the housing and secure with the bulb fixture screw. 9. Slide the electronics board back into the HL-2000-FHSA, taking particular care to ensure that the wires do not come into contact with the fan blades.
-
Page 23: Index
Index bulb package contents, 6 replacement, 17 parts list, 15 bulb replacement pinout diagram, 18 diagram, 15 pinouts, 14 product-related documentation, iii diagrams, 10 bottom view, 12 bulb replacement, 18 setup, 5 pinout, 15 shutter control, 7 power supply, 10 specifications, 13 rear view, 11 side view, 11... - Page 24 Index 000-10000-070-02-201504...