Page 3
CIP Training C7200 Series Misfeed How do I clear a misfeed? Locating Jammed Paper If a misfeed occurs, remove the jammed paper by following the procedures indicated in the animation that appears on the screen and the sticker or sheet inside the front cover. A misfeed has occurred in the place corresponding to the letter displayed on the control panel.
CIP Training C7200 Series Misfeed • Multiple paper misfeed locations may be indicated at the same time. When this happens, check all the areas indicated. • If there is no misfed paper in the area you check first, see the other areas that are indicated. •...
Page 5
CIP Training C7200 SeriesS Misfeed Removing jammed paper when the procedure is not displayed on the control panel • (Note: Screenshots are provided for reference purpose only. Your display may vary depending on your operating system and device.) • Misfeed: When L is displayed •...
Page 6
CIP Training C7200 Series Misfeed • When removing paper misfeeds, do not turn off the power. If you do, the configured functions and values will be lost. • To prevent paper misfeeds, do not leave any torn scraps of paper inside the device. •...
Page 7
CIP Training C7200 SeriesS Misfeed A Misfeed: When A is displayed How do I clear a misfeed when A is displayed? Follow the procedure below to remove the jammed paper. 2. Lower lever A1, and then open the guide panel. 1.
Page 8
CIP Training C7200 Series Misfeed A 7. Remove the misfed paper, and then slide the 8. Close the front left and right covers. paper tray to its original position. Misfeed: When B is displayed How do I clear a misfeed when B is displayed? Follow the procedure below to remove the jammed paper.
Page 9
CIP Training C7200 Series Misfeed B 5. Remove the misfed paper, and then 6. If you cannot remove the misfed paper, turn close the cover. knob B6 counterclockwise. 7. Remove the misfed paper. 8. Open cover B7, and then check that there is no paper.
Page 10
CIP Training C7200 SeriesS Misfeed B1 2. Lower lever A1, and then open the 1. Open the left and right front covers. guide panel. 3. Remove the misfed paper. 4. Raise lever A1 to its original position. 5. Lower lever B1, and then open the guide 6.
Page 11
CIP Training C7200 SeriesS Misfeed B3 1. Open the left and right front covers. 2. Turn knobs B3 and B4 counterclockwise until the LED light is off. 3. Close front left and right covers.
Page 12
CIP Training C7200 SeriesS Misfeed C Misfeed: When C is displayed How do I clear a misfeed when C is displayed? Follow the procedure below to remove the jammed paper. 2. After LED blink, lower levers B5 and 1. Open the left and right front covers. C1 to the left.
Page 13
CIP Training C7200 SeriesS Misfeed D Misfeed: When D is displayed How do I clear a misfeed when D is displayed? Follow the procedure below to remove the jammed paper. 2. After LED blink, lower levers B5 and 1. Open the left and right front covers. C1 to the left.
Page 14
CIP Training C7200 SeriesS Misfeed D 5. Remove the misfed paper. 6. Close guide panel D3, and then guide panel D2. 8. Check that there is no paper, and then 7. Open guide panel D4. close guide panel D4.
Page 15
CIP Training C7200 SeriesS Misfeed D 10. Remove the misfed paper, and then 9. Open guide panel D5. close guide panel D5. 12. Turn knobs D7 and D8 11. Open guide panel D6. couterclockwise at the same time. 13. Remove the misfed paper, and then 14.
Page 16
CIP Training C7200 SeriesS Misfeed D 15. Raise lever C1 to its original position. 16. Close front left and right covers. Misfeed: When D1 is displayed 2. Open the guide panel inside of the finisher. 1. Open the left and right front covers. 3.
Page 17
CIP Training C7200 Series Misfeed D1 5. If the LED does not turned off, turn 6. Close the guide panel and finisher knob D1 counterclockwise, and then front cover. check the LED light is off. 7. Close front left and right covers. Misfeed: When E is displayed How do I clear a misfeed when E is displayed? Follow the procedure below to remove the jammed paper.
Page 18
CIP Training C7200 Series Misfeed E 3. Check that there is no paper in the 4. Close front left and right covers. paper feed. Misfeed: When P is displayed How do I clear a misfeed when P is displayed? Follow the procedure below to remove the jammed paper. 1.
Page 19
CIP Training C7200 SeriesS Misfeed P 5. If you cannot remove the misfed 6. Slide lever P. original, open the ADF. 8. Remove the misfed original. 7. Open the cover. 9. Close the cover and ADF.
Page 20
CIP Training C7200 SeriesS Misfeed Q1 - Q2 Misfeed: When Q1 - Q2 is displayed How do I clear a misfeed when Q1 - Q2 is displayed? Follow the procedure below to remove the jammed paper. 2. Remove the misfed paper, and then 1.
Page 21
CIP Training C7200 Series Misfeed Q1 - Q2 5. Open the interposer main cover 6. Turn knob Q1 to counterclockwise, and right cover. and then remove the misfed paper. 7. Close the interposer main cover and right cover.
Page 22
CIP Training C7200 SeriesS Misfeed Q3 - Q4 Misfeed: When Q3 - Q4 is displayed How do I clear a misfeed when Q3 - Q4 is displayed? Follow the procedure below to remove the jammed paper. 2. Turn knob Q2 counterclockwise, and 1.
Page 23
CIP Training C7200 SeriesS Misfeed Q3 - Q4 6. If you cannot remove the misfed 5. Slide the guide panel to its original paper, press Q4. position. 7. Lower the guide panel. 8. Remove the misfed paper. 10. Close the interposer main cover and 9.
Page 24
CIP Training C7200 Series Misfeed U Misfeed: When U is displayed How do I clear a misfeed when U is displayed? Follow the procedure below to remove the jammed paper. 1. Open the two-tray wide LCT front 2. Check the LED lights are flashing. cover.
Page 25
CIP Training C7200 Series Misfeed U 7. Turn knob U6 clockwise. 8. Remove the misfed paper, and then check the LED light is off. 9. Turn knob U7 clockwise until the 10. Remove the misfed paper, and paper stops moving. then check the LED light is off.
Page 26
CIP Training C7200 SeriesS Misfeed U2 1. Open the two-tray wide 2. Check the LED lights are flashing. LCT front cover. 3. Lower lever U1. 4. Move lever U2 up and down for 5 to 6 times. 5. Turn knob U3 counterclockwise. 6.
Page 27
CIP Training C7200 SeriesS Misfeed U2 - U5 7. Raise lever U1 to its original position. 8. Close the two-tray wide LCT front cover. 9. Pull the two-tray wide LCT paper tray, 10. Slide the two-tray wide LCT tray and then remove the misfed paper. to its original position.
Page 28
CIP Training C7200 Series Misfeed U5 3. Lower lever U4. 4. Move lever U5 up and down for 5 to 6 times. 5. Turn knob U6 clockwise. 6. Remove the misfed paper, and then check the LED light is off. 7.
Page 29
CIP Training C7200 SeriesS Misfeed U5 9. If you cannot remove the misfed 10. Remove the misfed paper. paper, pull out the two-tray wide LCT lower paper tray. 11. Slide the two-tray wide LCT lower paper tray in to the device. Misfeed: When U8 is displayed How do I clear a misfeed when U8 is displayed? Follow the procedure below to remove the jammed paper.
Page 30
CIP Training C7200 SeriesS Misfeed U8 3. Open the two-tray wide LCT front 4. Lower lever U1. cover. 5. Turn knob U8 counterclockwise. 6. Remove the misfed paper. 7. Raise lever U1 to its original position. 8. Close the two-tray wide LCT front cover.
Page 31
CIP Training C7200 Series Misfeed U10 1. Open the two-tray wide LCT 2. Raise lever U9. front cover. 3. Turn knob U10 clockwise until LED 4. Remove the misfed paper. light is off. 5. Lower lever U9 to its original position. 6.
Page 32
CIP Training C7200 Series Misfeed U10 7. If you cannot remove the misfed 8. Open the cover. paper, pull out the two-tray wide LCT tray. 9. Remove the misfed paper. 10. Close the cover. 11. Slide the two-tray wide LCT tray in to the device.
Page 33
CIP Training C7200 Series Misfeed U11 1. Open the bridge unit of two-tray 2. Raise lever U11. wide LCT front cover. 3. Turn knob U12 clockwise. 4. Remove the misfed paper. 5. Lower lever U11 to its original position. 6. Close the bridge unit of two-tray wide LCT front cover.
Page 34
CIP Training C7200 SeriesS Misfeed V 1. Slide the multi bypass tray unit to 2. Remove the misfed paper. the right. 3. Slide the multi bypass tray unit to its original position. Misfeed: When Z is displayed How do I clear a misfeed when Z is displayed? Follow the procedure below to remove the jammed paper.
Page 35
CIP Training C7200 Series Misfeed Z3 5. Check the LED light is off, and then 4. Turn knob Z2 counterclockwise to raise lever A1 to its original position. remove the misfed paper. 6. After the LED flash, lower lever C1 to the left. 8.
Page 36
CIP Training C7200 SeriesS Misfeed Z3 10. Slide the unit to its original position. 11. Raise lever C1 to its original position. 12. Close front left and right covers. Misfeed: When Z4 is displayed 2. Lower lever A1, and then open the guide panel. 1.
Page 37
CIP Training C7200 Series Misfeed Z4 5. Check the LED light is off, and then 4. Turn knob Z2 counterclockwise to raise lever A1 to its original position. remove the misfed paper. 6. After the LED is flashing, lower lever B5 to the left. 7.
Page 38
CIP Training C7200 Series Misfeed Z4 10. Slide the unit to its original position. 11. Raise lever B5 to its original position. 12. Close front left and right covers.
Page 39
CIP Training C7200 Series Misfeed L Misfeed: When L is displayed How do I clear a misfeed when L is displayed? Follow the procedure below to remove the jammed paper. 1. Open the stacker upper cover. 2. Raise lever L1, and then remove misfed paper. Return the lever L1 to its original position.
Page 40
CIP Training C7200 SeriesS Misfeed Mc1 - MC4 Misfeed: When Mc1 - MC4 is displayed How do I clear a misfeed when Mc1 - Mc4 is displayed? Follow the procedure below to remove the jammed paper. 1. Open the front right and front left covers of the ring binder.
Page 41
CIP Training C7200 SeriesS Misfeed Mc5 or Mc6 Misfeed: When Mc5 or Mc6 is displayed How do I clear a misfeed when Mc5 or Mc6 is displayed? Follow the procedure below to remove the jammed paper. 1. Open the front right and front left covers of the ring binder.
Page 42
CIP Training C7200 Series Misfeed Mc7 or Mc8 Misfeed: When Mc7 or Mc8 is displayed How do I clear a misfeed when Mc7 or Mc8 is displayed? Follow the procedure below to remove the jammed paper. 1. Open the front right cover of the ring binder.
Page 43
CIP Training C7200 SeriesS Misfeeds Mk1 or Mk2 Misfeed: When Mk1 or Mk2 is displayed How do I clear a misfeed when Mk1 or Mk2 is displayed? Follow the procedure below to remove the jammed paper. 1. Open the interposer and Mk1 2.
Page 44
CIP Training C7200 Series Misfeed Mk6 Misfeed: When Mk6 is displayed How do I clear a misfeed when Mk6 is displayed? Follow the procedure below to remove the jammed paper. 1. Open the front cover of the 3. Return lever Mk6 to its original bridge unit (to the right of position.
Page 45
CIP Training C7200 Series Misfeed Mk9 - Mk11 Misfeed: When Mk9 - Mk11 is displayed How do I clear a misfeed when Mk9 - Mk11 is displayed? Follow the procedure below to remove the jammed paper. 1. Check that the LED on the front right cover of the perfect binder is unlit.
Page 46
CIP Training C7200 Series Misfeed Mk12 - Mk14 Misfeed: When Mk12 - Mk14 is displayed How do I clear a misfeed when Mk12 - Mk14 is displayed? Follow the procedure below to remove the jammed paper. 1. Check that the LED on the front right cover of the perfect binder is unlit.
Page 47
CIP Training C7200 Series Misfeed N1 - N5 Misfeed: When N1 - N5 is displayed How do I clear a misfeed when N1 - N5 is displayed?Follow the procedure below to remove the jammed paper. 1. Open the multi-folding unit front cover.
Page 48
CIP Training C7200 Series Misfeed N6 - N22 Misfeed: When N6 - N22 is displayed How do I clear a misfeed when N6 - N22 is displayed? Follow the procedure below to remove the jammed paper. 1. Turn knob N6 15 to 16 times clockwise. 2.
Page 49
CIP Training C7200 SeriesS Misfeed N6 - N22 13. Close the cover N15. 14. Return levers N13 and N14 to their original positions. 15. Lower lever N17 to the right, pull lever N18 to the right, and then remove misfed paper. 16.
Page 50
CIP Training C7200 Series Misfeed Rb1 – Rb5 Misfeed: When Rb1 – Rb5 is displayed How do I clear a misfeed when Rb1 – Rb5 is displayed? Follow the procedure below to remove the jammed paper. 1. Open the finisher front cover. 2.
Page 51
CIP Training C7200 Series Misfeed Rb6 – Rb9 Misfeed: When Rb6 – Rb9 is displayed How do I clear a misfeed when Rb6 – Rb9 is displayed? Follow the procedure below to remove the jammed paper. 1. Open the finisher front cover. 2.
Page 52
CIP Training C7200 Series Misfeed Rb12 – Rb13 Misfeed: When Rb12 – Rb13 is displayed How do I clear a misfeed when Rb12 – Rb13 is displayed? Follow the procedure below to remove the jammed paper. 1. Open the finisher front cover. 2.
Page 53
CIP Training C7200 SeriesS Misfeed Rb12 – Rb13 6. Return lever Rb13 to its original position 7. Turn knob Rb14, and then remove misfed paper. 8. Lower lever Rb15, and then turn knob Rb16. Then remove misfed paper. 9. Raise lever Rb17, and then remove misfed paper.
Need help?
Do you have a question about the Pro C7200 Series and is the answer not in the manual?
Questions and answers