Disposal; Electromagnetic Compatibility Information - Nakanishi NSK iProphy mobile Operation Manual

17

Disposal

Dispose of the stand and AC adaptor as industrial waste according to local laws and regulations.
Dispose of the motor handpiece as medical waste.
The motor handpiece includes a battery pack (lithium-ion battery). Do not dispose of in a fire or heat it. Doing
so may cause rupture of the battery pack, scattering of the battery fluid, overheating, smoking, rupture, or
explosion.
The battery pack (lithium-ion battery) included in the motor handpiece is a recyclable precious resource.
When disposing of it do not disassemble the battery pack and dispose of the product according to laws and
regulations. Alternatively, return it to your dealer.
18

Electromagnetic Compatibility Information

Guidance and manufacturer's declaration - Electromagnetic Emissions
The product is intended for use in the electromagnetic environment specified below. The customer or the user of the product should assure that it is used in such an
environment.
Emissions test
RF emissions
CISPR11
RF emissions
CISPR11
Harmonic emissions
IEC61000-3-2
Voltage fluctuations/flicker emissions
IEC 61000-3-3
Guidance and manufacturer's declaration - Electromagnetic Immunity
The product is intended for use in the electromagnetic environment specified below. The customer or the user of the product should assure that it is used in such an
environment.
Immunity test IEC60601 test level
Electrostatic discharge (ESD) ±(2, 4, 6)kV contact
IEC61000-4-2 ±(2, 4, 8)kV air
Electrical fast transient/burst ±2kV for power supply lines
IEC61000-4-4 ±1kV for input/output lines
Surge ±1kV line(s) to line(s)
IEC61000-4-5 ±2kV line(s) to earth
Voltage dips, short <5% Ut (>95% dip in Ut)
interruptions and voltage for 0.5 cycles
variations on power supply
40% Ut (60% dip in Ut)
input lines
for 5 cycles
IEC61000-4-11
70% Ut (30% dip in Ut)
for 25 cycles
<5% Ut (<95% dip in Ut)
for 5 sec
Power frequency 3 A/m
(50/60Hz)magnetic field
IEC61000-4-8
NOTE: 'Ut' is the AC mains voltage prior to application of the test level.
Compliance Electromagnetic environment - guidance
Group 1 The product uses RF energy only for its internal function. Therefore, its RF emissions are very low
Class B and are not likely to cause any interference in nearby electronic equipment.
The product is suitable for use in all establishments, including domestic establishments and those
Group 1
directly connected to the public low-voltage power supply network that supplies buildings used for
Class B
domestic purposes.
Not Applicable
Not Applicable
Compliance level
±(2, 4, 6)kV contact
±(2, 4, 8)kV air
±2kV for power supply lines
±1kV for input/output lines
±1kV line(s) to line(s)
±2kV line(s) to earth
<5% Ut (>95% dip in Ut)
for 0.5 cycles
40% Ut (60% dip in Ut)
for 5 cycles
70% Ut (30% dip in Ut)
for 25 cycles
<5% Ut (<95% dip in Ut)
for 5 sec
3 A/m
Electromagnetic environment - guidance
Floors should be wood, concrete or ceramic tile. If floors are
covered with synthetic material, the relative humidity should
be at least 30%.
Mains power quality should be that of a typical commercial
or hospital environment.
Mains power quality should be that of a typical commercial
or hospital environment.
Mains power quality should be that of a typical commercial
or hospital environment. If the user of the product requires
continued operation during power mains interruptions, it is
recommended that the product be powered from an
uninterruptible power supply or a battery.
Power frequency magnetic fields should be at levels
characteristic of a typical location in a typical commercial or
hospital environment.
15