Related Manuals for Mitsubishi Electric MP-G10-AH
Summary of Contents for Mitsubishi Electric MP-G10-AH
- Page 1 INDUSTRIAL SEWING MACHINE Attachment MODEL MP-G10-AH TECHNICAL MANUAL Label Holder Unit A180E639P03...
-
Page 2: For Safe Use
FOR SAFE USE Before the installation, operation, and inspection for this product, read the “FOR SAFE USE” and the technical manuals carefully. Also read the other technical manuals, “Sewing Machine Head”, “Control Unit” and “Operation Panel” describing some instructions, which are not in this manual, and use the sewing machine properly. -
Page 3: Specifications
Superimposed stitching or backstitching can be done at the start and end of stitching. 2. Specifications ： MP-G10-AH (pneumatic type label holder unit) Name ： PLK-G1010 Applicable model: ：... - Page 4 3. Configuration ★ The Fig. numbers in the drawing correspond to the part numbers given in the following explanations. 3.1 Clamp mechanism - 2 -...
- Page 5 3.1 Clamp mechanism (Parts list) 部品コード 品 名 Description 数 量 № Parts № Amt. Req. M 9 1 0 5 5 0 2 0 ﾛｯｶｸｱﾅﾂｷﾄﾒﾈｼﾞ M4X4 Screw M4X4 MH1 0A0352 ｶﾗｰ Collar M 9 0 5 1 9 0 5 0 ﾅｲﾛﾝﾜｯｼｬ Nylon washer M 9 1 1 0 9 0 0 2 ﾋﾗﾈｼﾞ...
- Page 6 3.2 Pneumatic pressure control unit 3.3 Accessories - 4 -...
- Page 7 3.2 Pneumatic pressure control unit (Parts list) 部品コード 品 名 Description 数 量 № Parts № Amt. Req. MH25A1601 ﾚｷﾞｭﾚｰﾀﾄﾘﾂｹｲﾀ Valve mounting plate M 9 1 0 6 6 0 0 4 SW-PW ﾂｷP ﾅﾍﾞﾈｼﾞ M 4×25 Screw M 4×25 MB10H0599 ﾃﾞﾝｼﾞﾍﾞﾝｸﾐﾀﾃ...
-
Page 8: Setup Procedures
4. Setup procedures CAUTION Always make sure that the power is OFF bef ore starting setting work. 4.1 Installing the clamp drive mechanism (1) Remove the four screws on the Y axis movement race side fixing the work holder arm (Fig. No. - Page 9 Cable Signal name Connection White Sewing machine head Connector Work holder input 2 CON L (12P) - ① (I8) Sewing machine head Connector Black CON L (12P) - ② Solenoid Sewing machine head connector PCB valve White ＋24V CON13 (FU)－② Blac k Sewing machine head connector PCB Work holder output 1...
- Page 10 4.6 Setting change CAUTION If the sewing machine is operated with the magnetic clamp settings, faults could occur. Always change setting for the pneumatic type clamp. (1) Points changed in setting details Please change setting as follows. *Refer to the clause of [14] Input/output setting mode and [15] Program mode of the technical manual ”Operation Panel”...
-
Page 11: Adjusting The Home Position
5. Home position 5.1 Adjusting the home position If the machine's home position is at the same position even if the label size changes, it will be easier to make a clamp and change it. Thus, change the home position in anticipation of the maximum size. - Page 12 6. Preparing to stitch labels Start of stitching End of stitching 6.1 Stitching conditions (1) Stitching size Label holder（mm） Min. Min. Fig. 1 (Look ing from front of sewing machine) (2) Stitching material thickness: 4mm or less (3) Superimposed stitching length (Fig. 1 T dimension) ... 12mm or less (4) Restrictions Input the stitching data in a clockwise direction (direction of bold arrow in Fig.
- Page 13 Fig. 2 6.4 Creating the stitching data Refer to the pattern in Fig. 1, and set points A to G Home position as shown in Fig. 3. (1) Press on the operation panel's standard screen. (2) Press the menu icon .
- Page 14 → point G → point A → (7) Using the arrows keys, input point F point B (8) Select , and then press (9) When is pressed, the stitching data will be created and written in. This completes creation of the stitching data. - 12 -...
- Page 15 7. Stitching test (1) Select the stitching pattern. (Refer to the PLK-G1010 Control section instruction manual.) (2) Set the material to be stitched, and then press the [Black] side of the 2-pedal foot switch to lower the work holder. (3) Set the label under the label holder plate, and then press the 1-pedal foot switch to lower the label holder.
- Page 16 Printed in Japan...