Related Manuals for Mitsubishi Electric MP-G10-AH
Summary of Contents for Mitsubishi Electric MP-G10-AH
- Page 1 Industrial Sewing Machine TECHNICAL MANUAL Attachment for Electronic Pattern Sewing Machine Label Holder Unit Model MP-G10-AH A180E639P01...
-
Page 2: For Your Safety
All information in this technical manual are subject to change without notice. MITSUBISHI ELECTRIC CORPORATION has all the copyrights on this technical manual. Reprinting the parts or all of this technical manual is not allowed without permission. Explanations for the warning signs... -
Page 3: Specifications
Superimposed stitching or backstitching can be done at the start and end of stitching. 2. Specifications ： MP-G10-AH (pneumatic type label holder unit) Name ： PLK-G1010 Applicable model: ：... - Page 4 3. Configuration ★ The Fig. numbers in the drawing correspond to the part numbers given in the following explanations. 3.1 Clamp mechanism - 2 -...
- Page 5 3.1 Clamp mechanism (Parts list) 部品コード 品 名 Description 数 量 № Parts № Amt. Req. M 9 1 0 5 5 0 2 0 ﾛｯｶｸｱﾅﾂｷﾄﾒﾈｼﾞ M4X4 Screw M4X4 M H 1 0 A 0 3 5 2 ｶﾗｰ Collar M 9 0 5 1 9 0 5 0 ﾅｲﾛﾝﾜｯｼｬ...
- Page 6 3.2 Pneumatic pressure control unit 3.3 Accessories - 4 -...
- Page 7 3.2 Pneumatic pressure control unit (Parts list) 部品コード 品 名 Description 数 量 № Parts № Amt. Req. M H 2 5 A 1 6 0 1 ﾚｷﾞｭﾚｰﾀﾄﾘﾂｹｲﾀ Valve mounting plate M 9 1 0 6 6 0 0 4 SW-PW ﾂｷP ﾅﾍﾞﾈｼﾞ...
-
Page 8: Setup Procedures
4. Setup procedures CAUTION Always make sure that the power is OFF bef ore starting setting work. 4.1 Installing the clamp drive mechanism (1) Remove the four screws on the Y axis movement race side fixing the work holder arm (Fig. No. - Page 9 Cable Signal name Connection White Sewing machine head Connector Work holder input 2 CON L (12P) - ① (I8) Sewing machine head Connector Black CON L (12P) - ② Solenoid Sewing machine head connector PCB White valve ＋24V CON13 (FU)－② Blac k Sewing machine head connector PCB Work holder output 1...
- Page 10 4.5 Installing the setting CAUTION If the sewing machine is oper ated with the magnetic clamp settings, f aults could occur. (1) Installing the system software Always change setting f or the pneumatic type clamp. ① Turn the sewing machine power switch ON. (1) Points changed in setting details Please change setting as follows.
-
Page 11: Home Position
5. Home position 5.1 Adjusting the home position If the machine's home posit ion is at the same posit ion even if the label size changes, it will be easier to make a clamp and change it. Thus, change the home position in ant icipat ion of the maximum size. - Page 12 5.2 Return to home position (1) Turn the sewing machine power switch ON. (2) Conf irm that the work holder lowers when the f oot switch (2-pedal) [ Black] side is turned ON, and rises when the switch is turned ON ag ain. (3) Conf irm that the label holder lowers when the expanded f oot switch (1-pedal) is turned ON, and rises when the switch is turned ON again.
- Page 13 (2) As shown in Fig. 2 on the next page, mark the label holder to indicate the size obtained by subtracting the holder amount S from the stitching pattern position of the label to be sewn on. (At this time, the holder amount S is set to the size of the needle or more.
- Page 14 6.4 Creating the stitching data Refer to the pattern in Fig. 1, and set points A Home position to G as shown in Fig. 3. (1) Press on the operation panel's standard screen. (2) Press the menu icon . The Pattern Input Mode screen will open.
- Page 15 7. Stitching test (1) Select the stitching pattern. (Ref er to the PLK-G1010 Control sect ion instruct ion manual.) (2) Set the material to be stitched, and then press the [Black] side of the 2-pedal f oot switch to lower t he work holder. (3) Set the label under the label holder plate, and then press the 1-pedal f oot switch to lower the label holder.
- Page 16 MITSUBISHI ELECTRIC CORPORATION FACTORY AUTOMATION SYSTEM TOKYO BUILDING 7-3 2 chome, Marunouchi CHIYODA-KU, TOKYO 100-8310, JAPAN Phone : +81-3-3218-6510 Fax : +81-3-3218-6820 New publication, effective Oct.2011. Contents subject to change without notice...