Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BTC BCE 4816IM
Summary of Contents for BTC BCE 4816IM
- Page 1 CD-WRITER 4816IM CD-ReWritable Drive User’s Manual...
-
Page 2: Copyright Statement
C L A S S 1 L A S E R P R O D U C T A P P A R E I L A L A S E R D E C L A S S E 1 L A S E R K L A S S E 1 L U O K A N 1 L A S E R L A I T E P R O D U I T L A S E R... -
Page 3: Fcc Compliance Statement
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. -
Page 4: Table Of Contents
Table of Contents INTRODUCTION YSTEM EQUIREMENTS ACKAGE ONTENTS INSTALLATION NTERFACE ONNECTIONS ARDWARE NSTALLATION RIVER NSTALLATION Windows Environment OFTWARE NSTALLATION Windows Environment CONNECTION & OPERATION RONT ANEL TECHNICAL DATA TROUBLESHOOTING... -
Page 5: Introduction
INTRODUCTION CD-WRITER 4816IM is a half-height CD-ReWritable drive of standard IDE interface. It supports maximum 48x speed writing ability on CD-R discs, 16x speed on CD-RW discs and 48x speed reading performance. The drive backs up all writing modes and different CD formats and it automatically recognizes the media placed in the drive, whether a CD, a CD-R or a CD-RW. -
Page 6: Package Contents
♦ Pentium II 300MHz above with at least 64MB of memory ♦ Fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended.) ♦ IDE host interface supporting ATAPI MMC command ♦ Operating system: Microsoft Windows 95/98/ME or Windows NT/2000/XP Package Contents ♦... -
Page 7: Installation
INSTALLATION Host Interface Connections Most current mainboard models have two IDE ports (primary and secondary) which can connect two IDE cables. Two IDE cables allow you to connect up to four devices, but it is recommended that you separate IDE ports for your hard drive and your CD-ReWritable drive. -
Page 8: Hardware Installation
You may consider one of the two ways recommended below to connect your drive. ♦ To get the most stable performance for the CD-RW drive to write: Primary IDE Master: Hard Disk Primary IDE Slave: CD-ROM Drive Secondary IDE Master: CD-RW drive ♦... - Page 9 The red-edge of the IDE Cable must be connected to Pin 1 on the CD- ReWritable drive. 5. If you have a sound card that can be connected to this CD- ReWritable drive, you can connect the drive (as Audio-out) and the sound card (as Audio-in) with a 4-pin audio cable.
-
Page 10: Driver Installation
Driver Installation Windows Environment CD-WRITER 4816IM is a PnP device, and Windows 95/98/ME and Windows NT/2000/XP can automatically detect the drive and load the appropriate driver. If Windows cannot detect the drive, you can operate manually: Click the Control Panel Icon in My Computer and then click Add New Hardware. -
Page 11: Connection & Operation
CONNECTION & OPERATION Front Panel BUSY 1. Headphone Plug By plugging in the headphone jack here, you can listen to an audio CD (CD-DA disc) directly playing from the CD-ReWritable drive. 2. Headphone Volume Control This knob adjusts the audio output level. Turn the wheel to the right to increase the audio volume of your headphone. -
Page 12: Rear View
this hole for manual ejection. Please make sure to power off the system before you do that. 6. Play/Skip button Press this button to play tracks or skip to next track during the playing state. 7. Close/Eject button This button opens and closes the disc tray. If the tray is closed, pressing the button will eject it. - Page 13 CD-WRITER 4816IM 3. Device Configuration Jumper Set the jumper to Master, Slave or Cable Select according to your system configuration. 4. IDE Interface Connector Plug one end of the 40-pin IDE cable here to join the 40-pin IDE connector on the motherboard. The red-edge of the IDE cable must be connected to Pin 1 of each connector.
-
Page 14: Technical Data
TECHNICAL DATA Performance Transfer rate Access time Data buffer CD format support Writing modes Writing speed Specification Interface Form factor Disc loading Read: 7200kb/s (up to 48X) Write: CD-R 7200kb/s(up to 48X) CD-RW 2400kb/s(up to 16X) 85ms at ⅓ stroke (48X CD-ROM) 180ms at full stroke(48X CD-ROM) 99ms at ⅓... - Page 15 Audio output level Power Dimensions Height Width Depth Weight Disc Specification Capacity 120mm disc: 63min 74min 80min 80mm disc: 18min 21min Disc Type Environment Temperature Operating temperature Non-operating temperature Line out = 0.6 ± 10%Vrms Headphone out = 0.6± 10%Vrms 5 VDC &...
- Page 16 Humidity Operating humidity Non-operating humidity 8% ~ 80%RH 5% ~ 95%RH...
-
Page 17: Troubleshooting
TROUBLESHOOTING To help you get more familiar with CD-WRITER 4816IM, the following FAQ lists some common problems you might encounter. Please read it for reference before you request RMA support from your dealer. Q1. CD-WRITER 4816IM cannot be recognized. (1) The drive might not be connected properly. Please check whether the IDE cable and power connector are tightly connected. - Page 18 Please check if the power cord is connected securely. Q6. The tray cannot be ejected. There are two possible reasons: (1) Need to be ejected by the application. Some of the burning or playing application will lock the drive. You have to eject by application and close it so as to restore the use of panel buttons.
- Page 19 (4) Increase main memory capacity. (5) Select other burning software. (6) De-fragment the hard disk. (7) Keep the source & destination discs clean. (no scratches, fingerprints or contamination.) (8) Copy data as image file to hard drive to avoid buffer underrun. (9) Keep the system clean.
- Page 20 3100550470 Version 1.0 June 2002...
Need help?
Do you have a question about the BCE 4816IM and is the answer not in the manual?
Questions and answers