Subscribe to Our Youtube Channel
Related Manuals for Light O Rama CMB24D DMX
Summary of Contents for Light O Rama CMB24D DMX
- Page 1 CMB24D DMX 24 Channel DC Controller User Manual June 1, 2013 V1.00 Copyright © Light O Rama, Inc. 2013...
-
Page 2: Table Of Contents
To allow your PC to communicate with this controller, Input Header (JP4) ..........11 you will need one of Light O Rama’s RS485 Current Handling Considerations ....... 12 adapters. When you purchase the Generic Starter Nitty-Gritty ............13 ... -
Page 3: What's In The Box
CMB24D CMB24D Caution: Although most applications for this Metal Tab Transistor Consideration product use low voltages, this product may be CMB24D boards have transistors with metal tabs. used with dangerous DC voltages. It is important Heat sinks are not required if the current draw per that you have an understanding of electrical channel is 4 amps or less. -
Page 4: Quick Start Guide
CMB24D CMB24D Put a lock washer on each screw and a bolt, don’t Hardware Fundamentals tighten the bolts yet. Do the same for the other ten screws. Now tighten but don’t over-tighten the bolts. Repeat the process for the other channel bank. Quick Start Guide This section assumes you have previous Light O Rama hardware experience. -
Page 5: Reset The Cmb24D
The controller is not connected to an Settings section for the mapping of your desired active Light O Rama network or DMX universe. LOR/DMX address to DIP switch settings. LED is on solid: The controller is connected to an Legal LOR Network unit IDs are ‘01’... -
Page 6: Channel Power Outputs
CMB24D CMB24D You may use different voltages on channel banks 1- If you use a toggle switch, the sequence will run until 12 and 13-24. The ground between the two channel the switch it turned off. banks is common, but you must use both grounds The sequence always runs to completion, even if the when using the board to switch more than 30 amps. -
Page 7: Nitty-Gritty
CMB24D CMB24D it, it needs a heat sink. If your voltage is higher where it might be dangerous to touch the metal tab of the transistor, use a thermometer. Nitty-Gritty This section is for technical types who are not sure whether their application would be a good match for If you have one of the USB adapters (shown center the CMB24D. -
Page 8: Designing And Playing A Sequence
CMB24D CMB24D controller and use the sliders and buttons in this no restriction on the types of controllers in this section to test your controller. network. The sequence is designed and tested using the Designing and Playing a Sequence Showtime Software Sequence Editor. When you are Lighting commands for your shows are called happy with the sequence, save it and stop the Sequences and are designed and implemented... -
Page 9: Refresh In The Hwu Fails To Find The Controller
CMB24D CMB24D If you are not sure which COM port is the RS485 Refresh in the HWU fails to find the adapter and you have a serial port RS485 adapter, controller you will have to consult your PC’s documentation; it Make sure the LOR/DMX Network Selection is normally COM1, COM2 or COM3. -
Page 10: Dip Switch Address Settings
CMB24D CMB24D the Hardware Utility and click the Refresh button to DIP Switch Address Settings find your controller(s). Select the one you want to update from the drop-down menu to the right of the ‘1’ means On and ‘0’ means Off. Refresh button. - Page 11 CMB24D CMB24D 39 27 0 0010 0111 295 1 0010 0111 83 53 0 0101 0011 339 1 0101 0011 40 28 0 0010 1000 296 1 0010 1000 84 54 0 0101 0100 340 1 0101 0100 85 55 0 0101 0101 341 1 0101 0101 41 29 0 0010 1001 297 1 0010 1001 42 2A 0 0010 1010 298 1 0010 1010 86 56 0 0101 0110 342 ...
- Page 12 CMB24D CMB24D 127 7F 0 0111 1111 383 1 0111 1111 171 AB 0 1010 1011 427 1 1010 1011 128 80 0 1000 0000 384 1 1000 0000 172 AC 0 1010 1100 428 1 1010 1100 129 81 0 1000 0001 385 1 1000 0001 173 AD 0 1010 1101 429 1 1010 1101 130 82 0 1000 0010 386 1 1000 0010 174 AE 0 1010 1110 430 ...
- Page 13 CMB24D CMB24D 215 D7 0 1101 0111 471 1 1101 0111 216 D8 0 1101 1000 472 1 1101 1000 217 D9 0 1101 1001 473 1 1101 1001 218 DA 0 1101 1010 474 1 1101 1010 219 DB 0 1101 1011 475 1 1101 1011 220 DC 0 1101 1100 476 1 1101 1100 221 DD 0 1101 1101 477 1 1101 1101 222 DE 0 1101 1110 478 ...
-
Page 14: Specifications
CMB24D Specifications Configuration Two banks of 12 channels Individual Channel 4 amps – No Heat Sinks Capacity 8 amps – Regular Heat Sinks Individual Bank Capacity 30 amps Board Capacity 60 amps Channel Supply Voltage 5 to 30 volts DC (Bank voltages may be different) Auxiliary Power Barrel 12 volts DC (center pin of barrel...
Need help?
Do you have a question about the CMB24D DMX and is the answer not in the manual?
Questions and answers