Panasonic FM-252-4(-P) Instruction Manual

,QWHJUDWHG ,QGLFDWRU 7\SH IRU *DV )ORZ 6HQVRU
FM-200 Series
D2-255025-A
Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thoroughly for the correct and
optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
Never use this product in a device for personnel protection.
In case of using devices for personnel protection, use products which meet
laws and standards, such as OSHA, ANSI or IEC etc., for personnel protec-
tion applicable in each region or country.
1 PART DESCRIPTION
Main display
(Green / Red)
MODE key
Sub display (Green / Red)
Connector area for
cable with connector
Connector area
for piping
(Note 2)
1RWHV  'LUHFWLRQ RI WKH DUURZ LQGLFDWHV WKH IRUZDUG GLUHFWLRQ RI ÀRZ UDWH ZKHQ VHWWLQJ WKH ÀRZ
GLUHFWLRQ WR ELGLUHFWLRQ RU RQHVLGH IRUZDUG GLUHFWLRQ :KHQ VHWWLQJ WKH ÀRZ GLUHFWLRQ WR
one-side reverse direction, a direction opposite to the forward direction display will be the
IRUZDUG GLUHFWLRQ RI WKH ÀRZ UDWH )RU VHWWLQJ ÀRZ GLUHFWLRQ UHIHU WR ³Flow direction set-
ting´ LQ ³ PRO MODE."
2) ø4 push-in joint / ø8 push-in joint is incorporated into FM- -4 (-P) / FM- -8 (-P), respec-
tively. The push-in joint is not incorporated into the aluminum body type.
2 PIPING
7KH IROORZLQJ VSHFL¿HG WXEH VKRXOG EH XVHG WR LQVHUW WR WKH SXVKLQ MRLQW W\SH
product.
Material of tube Tube diameter
Before using the product,
make sure to check that
Polyurethane
WKH WXEH LV ¿UPO\ LQVHUWHG
,QVWDOO D ¿OWHU DQ DLU GU\HU DQG DQ RLO PLVW ¿OWHU PLFURDOHVFHU RQWR WKH SULPDU\
side (upstream) of the product since the compressed air from the compressor
contains drain (water, oil oxide and foreign materials, etc.). Mesh (wire net) in the
SURGXFW LV XVHG WR UHFWLI\ WKH ÀRZ LQ WKH SLSH $OZD\V LQVWDOO D ¿OWHU WR WKH SULPDU\
VLGH RI WKH SURGXFW VLQFH WKLV PHVK LV QRW D ¿OWHU WR UHPRYH IRUHLJQ PDWHULDOV HWF
Pneumatics Air dryer Filter
pressure
source
:KHQ XVLQJ D YDOYH RQ WKH SULPDU\ VLGH RI WKH SURGXFW RQO\ XVH DQ RLOSURKLELW VSHFL¿FD-
tion valve. The product may malfunction or break if subject to splattering grease or oil, etc.
:KHQ XVLQJ WKH SURGXFW ZLWK DGVRUSWLRQ YHUL¿FDWLRQ HWF DOZD\V LQVWDOO DQ DLU
¿OWHU ZKRVH ¿OWUDWLRQ SURSHUW\ LV —P RU OHVV RQWR WKH VXFWLRQ VLGH WR SUHYHQW
VXFWLRQ RI IRUHLJQ PDWHULDOV DQG ZDWHU )XUWKHUPRUH FRQVLGHU DWPRVSKHULF
dew point and ambient temperature of the product, use the product under the
conditions that dew condensations will not be formed in the inside of pipe.
In case of mounting commercial joint to the aluminum body type, apply a spanner on
the metal part of this product and tighten by the tightening torque of 16 to 18N·m.
If excessive torque is applied, the commercial joint or the main body may break.
When piping, care must be taken that foreign materials such as sealing tape
and adhesive must not enter into the inside. If the foreign materials are en-
tered, the product may malfunction or break.
Make sure to mount the joint when using the product with its secondary side (downstream)
LV RSHQ WR WKH DLU ,I WKH MRLQW LV QRW PRXQWHG WKH SRUW ¿OWHU RI WKH SURGXFW PD\ IDOO RII
3 WIRING
Connection method
Insert the cable with connector CN-F15-C1 (accessory) into the
connector area of this product and mount the connector cover.
Disconnection method
Remove the connector cover and pressing the release lever of the cable with
connector, pull out the connector.
Note: Do not pull by holding the cable without pressing the release lever, as this can cause cable
break or connector break.
<Terminal arrangement> (Sensor body)
Terminal Color code of the
No. cable with connector
1 Brown
2 Black
1 2 3 4 5
3 White
4 *UD\
5 Blue
Ramco National
INSTRUCTION MANUAL
0()0 1R9
Comparative output 1 indicator (Green)
Comparative output 2 indicator (Green)
UP key
DOWN key
Forward direction display
(Note 1)
Connector area
for piping
(Note 2)
Allowable diameter
Polyamid ø4, ø8 Within ±0.1mm
ø4 Within ±0.1mm
ø8 Within +0.1 / -0.15mm
Regulator Oil mist filter Flow sensor
(Micro-alescer) (This product)
Connector
cover
Terminal name
+V
CH1 (comparative output 1)
CH2 (comparative output 2 / external input)
Analogue voltage output
0V
800-280-6933 | nsales@ramcoi.com
4 MOUNTING
Horizontal mounting
Use M3 screw and the tightening torque should be 0.5N·m.
<Resin body type>
M3 screw
(Please arrange separately.)
Dimension
17mm
2-ø3.4
through-hole
Vertical mounting
Use M3 screw and the tightening torque should be 0.5N·m.
<Resin body type>
Dimension (Unit: mm)
2-M3
15.5
depth 5
M3 screw
(Please arrange separately.)
When using sensor mounting bracket
When mounting the product on the sensor mounting bracket MS-FM2-1 (op-
tional) or MS-FM2-2 (optional), use the M3 screw (length 6mm) attached to
the sensor mounting bracket. The tightening torque should be 0.5N·m.
Use M3 screw to mount the sensor mounting bracket on a sensing surface.
<Resin body type>
Use MS-FM2-1
Dimension (Unit: mm)
30
6
3.5
M3 screw
(Please arrange separately.)
M3 screw (length 6mm)
(Attached to MS-FM2-1)
5 I/O CIRCUIT DIAGRAMS
NPN output type
Terminal No.
Color code of cable with connector
(Brown) +V
(Black) CH1
(Comparative output 1)
(White) CH2 (Comparative output 2 / External input)
(Gray) Analogue voltage output
(Note 2)
$SSUR[ NŸ
(Blue) 0V
(Note)
Internal circuit Users' circuit
PNP output type
Terminal No. Color code of cable with connector
(Brown) +V
(Black) CH1
(Comparative output 1)
(White) CH2 (Comparative output 2 /
External input)
(Gray) Analogue voltage output
$SSUR[ NŸ
(Note 2)
(Blue) 0V
(Note)
Internal circuit Users' circuit
*1: When using CH2 as a comparative output 2
*2: When using CH2 as an external input
Non-voltage contact, NPN transistor or
DC 2-wire output
or
High (+5 to +V or Open): Invalid
Low (0 to +0.4V): Valid
Notes: 1) As for the aluminum body type, variable resistor (clamping voltage: approx. 40V) is con-
nected between the internal power circuit and the metal body to prevent breakdown of the
VHQVRU &RQQHFW WKH PHWDO ERG\ WR 9 RI SRZHU VXSSO\ RU IUDPH JURXQG )* RI D GHYLFH
that is connected to 0V. High potential and insulation resistance tests between the internal
power circuit and the metal body must not be done.
2) Short-circuit protection is not incorporated into the analogue voltage output.
Do not connect the power supply or capacitive load directly to the analogue voltage output.
6 OUTPUT MODE
7KH RXWSXW 2)) PRGH ZLQGRZ FRPSDUDWRU PRGH K\VWHUHVLV PRGH LQWH-
grated output mode or integrated pulse output mode can be selected as the
output mode for comparative output 1 and comparative output 2.
5HIHU WR ³Output mode and threshold value setting mode´ LQ ³
SETTING MODE" for details.
(Unit: mm)
27
<Aluminum body type>
Dimension
9.5
30
2-M3 depth 5
M3 screw
(Please arrange separately.)
<Aluminum body type>
Use MS-FM2-2
Dimension (Unit: mm)
30
40
M3 screw
(Please arrange separately.)
M3 screw (length 6mm)
(Attached to MS-FM2-2)
Load
(*1)
Load
50mA max.
+
12 to 24V DC
±10%
-
50mA max.
(*2)
50mA max.
50mA
(*3)
max.
+
12 to 24V DC
±10%
-
Load
Load
(*1)
*3: When using CH2 as an external input
Non-voltage contact, PNP transistor or
DC 2-wire output
or
High (+5 to +V): Valid
Low (0 to +0.6V or Open): Invalid
www.panasonicsensors.com
(Unit: mm)
13
6
3.5
MENU