Table of Contents
Advertisement
Available languages
Available languages
10
Control panel IN-7DDI, IN-88DDI models
2
1
3
6
5
4
7
1.
Temperature display
2.
„Work" diode
3.
„Set" diode
4.
Decrease value button
5.
Increase value button
6.
„Set" button
7.
ON/OFF switch (Applies to model IN-88DDI only)
IN-48DDI, IN-96DDIs models
3
4
1
2
5
9
8
7
6
1.
Humidity display
2.
Temperature display
3.
„Set" button
4.
Increase value button
5.
ON/OFF switch
6.
Decrease value button
7.
„Reset" button
8.
Display showing time left until next egg rocking
9.
Number of incubation days display
IN-56DDI model
1
2
7
3
4
6
5
1.
Display
2.
„Set" button
3.
Increase value button
4.
ON/OFF switch
5.
Decrease value button
6.
Egg candler switch
7.
„Reset" button
Display description:
1
2
3
7
4
6
5
EN
1.
Time countdown until next egg rocking.
2.
Temperature
3.
Humidity
4.
Egg candler light on
5.
Low/high humidity alarm
6.
Low/high temperature alarm
7.
Number of incubation days
Egg candler
1
1.
ON/OFF switch
OPERATION
The following tables present the summary of how many
eggs of a particular type can be incubated simultaneously
in the device and how they should be spaced.
Model
IN-
IN-
IN-
IN-
7DDI
48DDI
56DDI
96DDI
The
7
48
56
56
maximum
number of
hen eggs.
The
7
48
56
96
maximum
number of
pigeon, bird
and quail
eggs.
The
4
24
28
48
maximum
number of
turkey and
duck eggs.
The
1
16
18
32
maximum
number of
goose eggs.
Modell
IN-
IN-
IN-
IN-
7DDI
48DDI
56DDI
96DDI
How should
One egg in each egg tray hole.
hen, pigeon
and bird
eggs be
spaced.
How should
Leave one empty space (hole) between
turkey and
the eggs on the tray.
duck eggs
be spaced.
How should
Remove the egg tray and place
goose eggs
the eggs on the net.
be spaced
26.10.2018
IN-7DDI model
1.
Remove cover and lift egg tray.
2.
Pour water into the groove around the white mesh.
ATTENTION: Do not pour water into the white mesh
as that may damage the device!
3.
Attach cover.
4.
Connect the device to a power source.
5.
Select the required temperature: press the „SET" (6)
button. The „set" (3) diode will illuminate, indicating
that the device is in settings mode. Use „+" (5) and
„-" (4) buttons to select the temperature. Use the
„SET" (6) button to confirm. The „Work" (2) diode will
come on.
6.
Wait for the device to warm up (approx. 10-20 min.).
IN-
7.
Gently arrange the eggs on the tray.
88DDI
8.
Inspect the water level in the egg incubator regularly.
88
IN-48DDI, IN-96DDI models
1.
Lift the cover, pour water into the egg incubator.
Make sure the drive mechanism does remains dry.
Close the cover.
132
2.
Connect the device to a power source.
3.
Use the On/Off (5) switch to turn the device on.
4.
An alarm will sound. Disable the alarm by pressing
a button on the control panel.
5.
The device will automatically rock the eggs every
2 hours. The eggs are rocked to the left and right,
up to 45 degrees for 10 seconds. Do not lift the
44
cover during automatic egg turning. Pay particular
attention when using the incubator for the first time.
6.
Press the „reset" (7) button once to manually activate
the egg rocking function.
7.
Press and hold the „reset" (7) button to reset the next
rocking counter (it sets it back to 1:59).
29
8.
To reset the incubation day counter unplug the
device. Press and hold the "reset" button (7) during
plug in the device. Device's factory settings will be
restored.
IN-
9.
Setting the temperature:
88DDI
•
The egg incubator's temperature factory setting is
38°C.
•
Press the „Set" (3) button
•
Use buttons (4) and (6) to set the heating
temperature.
•
Press the „Set" (3) button to confirm the selection.
10.
Setting alarm values and calibration:
•
To enter settings mode press and hold the „Set" (3)
button for three seconds.
•
Use buttons (4) and (6) to switch between the
parameters shown in the table below.
Parameter
Parameter meaning
AL
Setting the low
temperature alarm.
AH
Setting the high
temperature alarm.
26.10.2018
EN
Parameter
Parameter meaning
AS
Setting the low humidity
alarm.
CA
Thermometer calibration.
HS
Setting the upper
temperature limit.
LS
Setting the lower
temperature limit.
•
To enter settings of the selected parameter, press
and hold the „Set" (3) button
•
Use buttons (4) and (6) to set alarm values. Wait for
the device to automatically return to the main menu.
•
The alarm emits a sound signal. To disable the alarm,
press a button on the control panel.
11.
Wait for the device to warm up (approx. 10-20 min.).
12.
Gently arrange the eggs on the tray.
13.
Inspect the water level in the egg incubator regularly.
IN-56DDI model
1.
Remove cover and lift egg tray. Carefully pour water
into the groove. Close the cover.
2.
Connect the device to a power source.
3.
Use the On/Off (4) switch to turn the device on.
4.
An alarm will sound. Disable the alarm by pressing
a button on the control panel.
5.
Setting the temperature:
•
The egg incubator's temperature factory setting is
38°C.
•
Press the „Set" (2) button
•
Use buttons „+" (3) and „-" (5) to set the heating
temperature.
•
Press the „Set" (2) button to confirm the selection.
6.
Setting alarm values and calibration – in accordance
with operating instructions point 10 for IN-48DDI
and IN-96DDI models
7.
Press and hold the „reset" (8) button to reset the next
rocking counter (it sets it back to 1:59).
8.
To reset the incubation day counter unplug the
device. Press and hold the "reset" button (8) during
plug in the device. Device's factory settings will be
restored.
9.
Wait for the device to warm up (approx. 10-20 min.).
10.
Gently arrange the eggs on the tray.
11.
Inspect the water level in the egg incubator regularly.
12.
Use button (6) to activate the egg candler and check
embryo development inside the egg.
IN-88DDI model
1.
Remove cover. Fill with water. Close the cover.
2.
Connect the device to a power source.
3.
Use the On/Off (7) switch to turn the device on.
4.
Select the required temperature: press the „SET" (6)
button. The „set" (3) diode will illuminate, indicating
that the device is in settings mode. Use „+" (5) and
„-" (4) buttons to select the temperature. Use the
Factory setting
„SET" (6) button to confirm. The „Work" (2) diode will
come on.
1°C
5.
Wait for the device to warm up (approx. 10-20 min.).
6.
Gently arrange the eggs on the tray.
7.
Inspect the water level in the egg incubator regularly
1°C
11
Factory setting
45%
0°C
39.5°C
30°C
Hide quick links:
Advertisement
Table of Contents
