Related Manuals for Hoshizaki DBF-25SB-AU
Summary of Contents for Hoshizaki DBF-25SB-AU
- Page 1 DRAFT BEER DISPENSER DBF-25SB-AU DBF-43SB-AU INSTRUCTION MANUAL L168QU111 (062012)
-
Page 2: Installation
IMPORTANT [13] Top cover 1. This booklet is an integral and essential part of the product and should be kept and preserved by the user. Please read carefully the guidelines and warnings contained herein as [b] ACCESSORIES they are intended to provide the installer/user with essential information for the proper installation and the continued safe Instruction manual 1 pc use and maintenance of the product. Please preserve this Brush 1 pc booklet for any further consultation that may be necessary. -
Page 3: Plumbing Connections
[1] Quick gas hose joint replaced by a qualified service engineer. [2] Beer hose adapter O-ring (P10A) * Usually an electrical permit and services of a licensed electrician are required. [3] Quick beer hose joint * If the supply cord is damaged, it must be replaced by a replacement [4] Beer hose cord available from Hoshizaki Parts/Service Centres. [5] Keg coupler * If the receptacle at the installation site is not earthed, use the screw Dispenses beer out of the keg. Consult with the liquor shop or beer at the rear of the unit to make an earth connection (an earth wire is company, and prepare a suitable keg coupler for the keg to be used. not provided and should be prepared in the field). [6] Beer keg * Do not connect the earth wire to a gas line, water line, lightning rod or telephone earth wire. Improper earthing may cause electric... -
Page 4: Trial Run
2) Cut the gas hose to have a vertical cutting plane. 1) Check that the unit is unplugged. 3) Insert the gas hose into the quick joints on the keg coupler and regulator. Pull the hose hard to check for tight connections. 2) Remove the top cover and inner cover. 4) Use the adjust dial to check for gas leaks. 3) [DBF-25SB-AU] Fill the water tank with tap water. The water tank overflows when IMPORTANT the water level reaches about 2 cm below the top of the water tank. Then stop pouring water. 1. Cut the gas hose with a specialized tool such as hose cutter. Do not use scissors, or the gas hose may be crushed to cause gas leaks. - Page 5 II. OPERATION 4) Attach the keg coupler on the new keg by turning it clockwise. Keg coupler 1. CHECKS BEFORE OPERATION (DAILY) [a] REPLACEMENT OF CO2 GAS CYLINDER 1) Close the main valve of the CO2 gas cylinder. 2) Adjust the regulator to “0”. 3) Remove the empty regulator from the CO2 gas cylinder, and cap it. Rotary type Vertical type 4) Follow the steps 1) to 4) in “I. 4. [a] CO2 GAS CYLINDER”. IMPORTANT 1. Wash the keg joint with water if necessary. IMPORTANT Carry a CO2 gas cylinder with its cap on and without shaking. 2. Do not loosen the ferrule on the keg. [b] CHECKS AND REPLACEMENT OF BEER KEG 5) Turn the regulator adjust dial clockwise to the appropriate gas pressure level specified by the beer company.
-
Page 6: Maintenance
3) To dispense foam, push the beer tap lever hard IMPORTANT toward the unit from the stop position. To stop If the beer circuit is not flushed with beer remaining on the foam, move the lever back to its original position. beer tap, the valve shaft jams inside the beer tap, resulting in unavailable, unstable, or continuous dispensing actions. In this case, disassemble and clean the beer tap in accordance with “III. 5. DISASSEMBLY AND CLEANING OF BEER TAP (WEEKLY)”. [d] END OF OPERATION [b] LEADING BEER TO TAP 1) Close the keg coupler, and remove it from the keg. Flush the beer 1) Check that the regulator adjust dial is set to the appropriate... - Page 7 1. BEER CIRCUIT (DAILY) 10) Turn the regulator adjust dial, and adjust the gas pressure to 0.15 MPa or the allowable range specified on the cleaning tank. IMPORTANT 11) Open the beer circuit. Use the cleaning tank specified by the beer company. Follow Rotary type: Turn the keg coupler handle clockwise until it stops. the operating instructions provided on the cleaning tank. Vertical type: Push down the keg coupler handle until it locks in place. 1) Close the beer circuit before flushing. Keg coupler handle Rotary type: Turn the keg coupler handle counterclockwise until it stops. Vertical type: Unlock and lift the keg coupler handle all the way Keg coupler handle Vertical type...
- Page 8 16) Turn the keg coupler counterclockwise, and remove it from the Through hole for cleaning tank. overflow hose Keg coupler Drain board Mounting screw Cleaning tank Rotary type Vertical type 17) Attach the keg coupler on the keg by turning it clockwise until it Overflow hose stops. Mounting hole Drain pan Keg coupler 4. CLEANING BEER CIRCUIT WITH SPONGE (WEEKLY) IMPORTANT 1. Store the used cleaning sponge for later use.
- Page 9 [Normal Operation] 17) Close the beer circuit. Rotary type: Turn the keg coupler handle counterclockwise. Vertical type: Unlock and lift the keg coupler handle all the way Cap nut Keg coupler handle [Sponge Cleaning] Rotary type Vertical type Valve shaft 18) Turn the keg coupler counterclockwise, and remove it from the Cleaning sponge cleaning tank. Keg coupler 8) Attach the beer tap on the unit by tightening the union nut.
- Page 10 1. GAS HOSE AND BEER HOSE (MONTHLY) Small hole Check the gas and beer hoses for damage, deformation, and water leak marks (stains). If any problem is found, contact an authorized Hoshizaki service company. 2. ATTACHMENT PLUG AND POWER CORD (ANNUALLY/ BIANNUALLY) Small hole...
- Page 11 3. COOLING WATER (BIANNUALLY) manual to the exterior to provide the new owner with information on safe and proper use of the product. 1) Unplug the unit. 2) Remove the top cover and inner cover. 3) Check that the cooling water level is about 2 cm below the top of the water tank (DBF-25SB-AU) or up to the standard water level marked on the tank (DBF-43SB-AU). If it is insufficient, refill the water tank with tap water. Refresh the cooling water twice a year. To refresh the cooling water: 4) Remove the drain pan. 5) Prepare a large container to receive drain water [about 6 L (DBF- 25SB-AU) or 8 L (DBF-43SB-AU) in ice storage]. Remove the drain...
Need help?
Do you have a question about the DBF-25SB-AU and is the answer not in the manual?
Questions and answers