Advertisement
OPERATION
1 .
,r.O"ration-First
vacuum carpet thoroughly, then
you are
ready
to
use your new Carpet Machine.
2.
,n"enctoseO bottle contains
a premixed
solution,
ready
to
use.
ln
the future,
it
is recommended you use concentrated Bissell 4 in
One
Carpet Formula. See
instructions on the enclosed bottle for mixing:
"Pour Carpet Formula to dotted line, add water to the top and mix."
3.
ntt""n
the water hose to any threaded kitchen or bathroom faucet.
Some
faucets
have
external threads and
others have internal
threads.
Most
have
aerators or screen
filters that unscrew. Unscrew the
aerator.
lf
use
of pliers is
necessary,
wrap
the aerator with tape to
avoid damage.
lf
an adapter
is
necessary
(see diagram B) screw
it
to
the faucet. Screw the water hose to the adapter. This should be
done
carefully and
slowly to avoid damaging threads. lf you must connect
to a
laundry type thread, an adaptor
can be purchased at the local
hardware store. There are also adaptors available
that will attach
to
threadless faucets.
4.
,r^"the
metering
line into the solution bottle. Keep hose
end
below
liquid.
.
Set your
faucet between warm and hot. Extreme hot water could
damage
the system.
Run
water prior
to attaching
hose
to
avoid
cold water start.
6.
,,un
in the
tank electrical cord to a wall receptacle and you
are
ready
to
clean your carpets!
7 .
,rror
ro
cleaning room, heavily soiled areas should be prespotted
This can be done by releasing cleaning solution spray with the
release
trigger, holding
the wand approximately 6 inches
over
the
heavily
soiled
areas.
This operation
can be done without the
vac
running and using only
the water pressure from your
faucet.
Once
you
have
prespotted
the heavily soiled
areas,
you can then
proceed
to
clean
the entire room as directed
below.
a
lCD.
Turn
on power by the on-off switch on the motor housing
unit.
.
Place
the suction foot on the carpet and with one hand engage the
injector
trigger releasing the spray of cleaning solution and hot water
into your carpet. Pull
the unit toward you so that the vacuum picks
up
the dirty water.
Use
gentle pressure for the best results
1
O.
Back and frcrth scrubbing
will
help loosen spots, a
final pass
over
the
carpet
with the vacuum ON only will help the carpet dry
faster.
11.
Prespot
traffic
areas
with quick initial pass, then clean entire
room.
Check
the liquid waste in the tank and empty before it
gets
too
heavy
to
handle. To empty,
stop the motor
and
remove
the plug from the wall receptacle. Deposit the
liquid waste contents into a suitable drain. After the
tank is empty, return the cover to its original position.
To
continue use, plug the cord into the wall receptacle
and
start the
motor.
f--:
w
-
wOShOt
F-
#
-
waSher
.4
adapter
-
waSher
Keep
hose end
below
liqu id
\\
z
-.7
/
12.|f
your exhaust begins
to spit
foam, immediately shut
off the
motor, unplug
the electrical cord and empty
contents
of
tank.
1
3.
When
finished with the cleaning job, clean the
tank,
wand,
filter
before
storing.
Rinse
the parts with
water.
lmportant:
After each
use,
take
the metering line from
the solution bottle and put into a container of
clean
water. Operate
the injector to flush system. This should
be done by holding
suction foot over sink or
bucket.
ffiffi
ltffi]ffi'/
l.ffimi93si""
I
INSIDE
TH
READ
(no adapter
needed)
Advertisement
