Audiovox CE506SLK Operating Instructions

Follow the advice below for safe and appropriate operations.
ON PLACEMENT FCC INFORMATION (For USA ONLY)
• Do not use the unit in places which are
This equipment has been tested and found
extremely hot, cold, dusty or humid.
to comply with the limits for a Class B digital
• Place the unit on a flat and even surface.
device, pursuant to Part 15 of the FCC Rules.
• Do not restrict the air flow of the unit by
These limits are designed to provide
placing it in a place with poor air flow, by
reasonable protection against harmful
covering it with a cloth, or by placing it on
interference in a residential installation. This
a carpet.
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
ON SAFETY
and used in accordance with the instructions,
• When connecting and disconnecting the
may cause harmful interference to radio
AC cord, grip the plug and not the cord
communications. However, there is no
itself. Pulling the cord may damage it and
guarantee that interference will not occur in
create a hazard.
a particular installation. If this equipment does
• When you are not going to use the unit
for a long period of time, disconnect the cause harmful interference to radio or
AC power cord.
television reception, which can be determined
by turning the equipment off and on, the
ON AC VOLTAGE
user is encouraged to try to correct the
• Before use, check that the rated voltage
interference by one or more of the following
of your unit matches your local voltage.
measures:
- Reorient or relocate the receiving
VENTILATION WARNING
antenna.
• The normal ventilation of the product shall
- Increase the separation between the
not be impeded for intended use.
equipment and receiver.
- Connect the equipment into an outlet
ON CONDENSATION
that is on a circuit different from the one
• When left in a heated room where it is
the receiver is connected.
warm and damp, water droplets or
- Consult the dealer or an experienced
condensation may form inside the CD
player. radio/TV technician for help.
• When there is condensation inside the
You are cautioned that any changes or
unit, the unit may not function normally.
modifications not expressly approved in this
• Let it stand for 1 to 2 hours before turning
manual could void your authority to operate
the power on, or gradually heat the room
this equipment.
up and dry the unit before use.
Should any trouble occur, disconnect the
AUX JACK
AC power cord and refer servicing to
AUX L
• To listen to audio
IN
qualified personnel.
signals from external
unit through this unit:
Connect the red plug
to the R jack, and the
R
white plug to the L jack
of the AUX in (on left side
connector.
of the unit)
-1-
TIMER OPERATION
TIMER PLAY
The power can be turned on automatically at a preset time so that you can wake up CD or
RADIO function.
Make sure the clock is correct before TIMER PLAY. Please refer to CLOCK setting procedures.
Note: The unit must be in 'STANDBY' mode to set the timer.
1. Press and hold TIMER button until the 6. Turn on the unit to select the desired
"TIMER" indicator blinks on the display. program source by pressing FUNCTION
button.
TUNER: select a BAND and a station
CD: Insert a disc
2. While "TIMER" indictor blinks on the
display, press and hold MEMORY button
about 3 seconds until hour blinks on the
display.
7. Set volume level and X-Bass, and then
press POWER button to standby mode.
3. Press TUNING / SKIP
buttons to set hour.
8. When the preset time reaches, the system
will turn on automatically and "TIMER"
indicator will blink on the display.
TIMER
4. Press MEMORY button. The minute will
blink.
9. If you want to snooze a few more minutes.
You can press SNOOZE button (on the
5. Press TUNING / SKIP
Remote Control), the system will go to
buttons to set minutes and press standby mode ("SNOOZE" indicator
MEMORY button to confirm, finally
appear on the display) and then turn on
"TIMER" indicator will stop blinking after
again 5 minutes later.
several seconds.
You can repeat this function as many as you
desired within 60 minutes from the preset
automatically PLAY timer.
-4-
PRECAUTIONS
1 2 3 4 5 6 7
16
15
22
1. CD DOOR OPEN/CLOSE button
2. PLAY/PAUSE button
3. PHONES jack
4. TUNING / SKIP
5. STOP/BAND / REPEAT/PRESET
button
6. MEMORY button
7. RANDOM button
8. SLEEP/TIMER/DISPLAY button
9. FUNCTION (CD/TUNER/AUX)/INTRO
button
10. VOLUME (-/+) controls
NOTE:
1. If you want to exit snooze mode, press
2. The preset auto play timer function will be active every day if it is not cancelled.
To cancel timer play function, press and hold TIMER button about 3 seconds until "TIMER"
indicator disappears on the display.
DISPLAY FUNCTION
1. In standby mode, press DISPLAY button
and you can check the auto play timer if it
has been set.
SLEEP SETTING
When the sleep timer is used, the power is automatically turned off after the specified time passes.
1. Press SLEEP button while the power is on.
"SLEEP 90" appears on the display.
Note: SLEEP can be adjusted in TUNER,
CD and AUX modes.
AM
NOTE: Once the sleep time reaches, the power will be turned off atuomatically.
TUNING IN TO A STATION MANUALLY
1. Press FUNCTION button to TUNER.
2. Press STOP/BAND button to select your
desired band (FM/AM).
SNOOZE
PARTS IDENTIFICATION
8 9 10 1112 13 14
21
17 18 19 20
11. X-BASS indicator
12. X-BASS button
13. POWER button
button 14. POWER ON indicator
15. LCD display
16. Remote sensor
17. CD door
18. FM Antenna wire
19. AM Loop Antenna
20. AC cord
21. AUX IN jack
22. Stand (optional)
-2-
POWER button to turn on the system.
2. In power on mode, press DISPLAY button
repeatedly and you also can check
system status, clock and auto play timer
if they have been set.
2. Press SLEEP button repeatedly to select the
length of remaining time until the unit turns
off.
It changes the indicator in the following way:
90 80
10 70
If the sleep timer is set, the word "SLEEP" will
SLEEP
be shown on the display.
To cancel the sleep timer, press SLEEP button
once and "SLEEP" disappears on the display.
LISTENING TO THE RADIO
3. Press TUNING / SKIP
buttons to select a station.
-5-
TURNING ON THE UNIT
PRESS POWER BUTTON
Press POWER button, the POWER ON indicator will light up. Select the desired function by
pressing FUNCTION button and the corresponding function indicator will be shown on the display.
TO TURN OFF THE UNIT
Press POWER button to STANDBY, the POWER ON indicator will go out and only clock
display will be shown.
1. In standby mode, press and hold 4. Press TUNING
MEMORY button until the time blinks on the buttons to set correct hour.
display.
2. Press TUNING / SKIP
5. Press MEMORY button, the MINUTE
buttons to set 12 Hour or 24 Hour
blinks.
timer format.
6. Press TUNING
buttons to set correct minutes, and then
press MEMORY button to start the
3. Press MEMORY button, the hour blinks.
clock.
ADJUSTING THE SOUND
To adjust volume To select x-bass
X-BASS is designed specifically to boost the
low frequency sound to obtain a more powerful
bass.
Note: Press X-BASS button, the indicator of
X-BASS will light up.
FOR PRIVATE LISTENING
Connect the headphone (Ø3.5 mm stereo mini-plug) to the PHONES jack.
When headphones are connected, the speakers are automatically disconnected.
-3-
FOR BETTER RECEPTION
FM AM
Fully unwind the wire antenna. Then extend Connect the loop aerial (provided) to the "AM
the wire antenna and place it in the position LOOP ANTENNA" snap terminals at the back
that sounds best. of the unit.
NOTE: DO NOT CONNECT TO AN OUTSIDE
ANTENNA.
TO SEARCH FOR A STATION AUTOMATICALLY
Press and hold TUNING / SKIP button for 1 to 2 seconds, and the tuner starts
searching for a station for automatically. After tuning in to a station, the search stops.
The search may not stop at a station with a very weak signal.
TO RECEIVE THE FM BROADCAST IN STEREO
When the reception is good, the "STEREO" indicator will appear on the display.
TUNER STEREO
FM
MHz
PRESETTING STATION
You may tuned in to a stored station directly by entering the preset number. It is possible to store
stations of any band in your choice order.
Manual memory presetting
This feature allows you to manually preset stations to any desired channel.
1. Set to the desired band and station. 3. Press REPEAT/PRESET button to
select a channel number for the preset
station.
4. Press MEMORY button to memorize the
2. Press MEMORY button, the MEMORY
station.
indicator blinks.
5. Repeat steps 1 to 4 for the next preset.
-6-
CLOCK SETTING
/ SKIP
/ SKIP
X -BASS