Advertisement
TUNING INTO A PRESET STATION
Press
REPEAT/PRESET button to select a preset number.
TUNER
FM
MEMORY
NOTE: If no button is pressed again within 10 seconds, the preset mode will be exited
automatically.
1. Press FUNCTION button to CD.
3. To start playing, press
PAUSE button.
2. Press
OPEN/CLOSE button to open
CD door. Place a disc in the CD tray with
the label face front and then press
TO INTERRUPT PLAYBACK
OPEN/CLOSE button to close it. The
Press
PLAY/PAUSE button.
total number of tracks will be shown on
The track time will blink.
the display.
To resume playback, press
button again.
TO STOP PLAYBACK
Press
STOP button.
NOTE:
• Do not push the CD door to close it.
• CD door cannot open when power is off.
Locating a particular point in a track
Searching for the beginning of a track
To move backward at high speed
To find a previous track
Keep SKIP
button pressed during
Press SKIP
the beginning of the current track.
playback and release at the desired point.
Press SKIP
To move forward at high speed
tracks backward one by one.
Keep SKIP
button pressed during
To skip tracks
playback and release at the desired point.
Press SKIP
track(s) forward one by one.
Keep it pressed
NOTE: The CD player may skip if high volume or x-bass levels are used.
-7-
TO REPEAT THE WHOLE DISC
Press
REPEAT/PRESET button a second time to repeat all tracks, the repeat all indicator
will be shown on the display.
CD
TO CANCEL REPEAT PLAY
Press
PRESET/REPEAT button until REPEAT indicator disappears.
INTRODUCTION PLAY
RANDOM PLAY
This function allows the first 10 seconds of each
All the tracks on the disc can be played in
track of the disc to be played.
random order.
Press INTRO button.
Press RANDOM button.
INTRO appears on the display.
RANDOM appears on the display and the
disc will play automatically.
CD
INTRO
To cancel introduction play.
To cancel random play.
Press
STOP or INTRO button so that
Press
STOP or RANDOM button so that
INTRO on the display goes out.
RANDOM on the display goes out.
REMOTE CONTROL
1. DISPLAY button
1
2.
STANDBY / ON button
2
3. FUNCTION (TUNER/CD/AUX) button
3
10
4. PRESET/REPEAT button
4
5.
STOP/BAND button
11
5
6.
TUNING /
12
7. MEMORY
button
6
8. RANDOM button
13
7
9. SLEEP button
14
8
10. SNOOZE button
11.
PLAY/PAUSE button
9
15
12.
TUNING/
13. X-BASS button
16
14. INTRO button
15. TIMER button
16. VOLUME +\- controls
-9-
PROGRAMMING TRACKS - in the CD stop mode
1. Press
MEMORY button.
MHz
CD
CD PLAYBACK
2. Press
TUNING
PLAY/
buttons to select your desired track.
CD
PLAY/PAUSE
To check the program
In stop mode, press
disc, track and program numbers will appear on
the display.
Press
MEMORY button again to view the
other programmed selections.
These displays do not appear on the display
during playback.
button once to return to
button repeatedly to skip
REPEAT PLAY
This function will allow a single track or all tracks on the disc to be played repeatedly.
button repeatedly to skip
TO REPEAT THE SAME TRACK
Press
REPEAT/PRESET button once during playback, the repeat one indicator will blink.
Press it once
USING THE REMOTE CONTROL CORRECTLY
•
Point the Remote Control at the REMOTE SENSOR located on the unit.
•
When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR
REPEAT
may be degraded, causing unreliable operation.
•
The recommended effective distance for remote operation is about 4 meters (13 feet).
TO CHANGE REMOTE BATTERY
1. Open the battery door.
ATTENTION
Take out the PVC sheet before operating the
Remote Control.
BATTERY REPLACEMENT
CD
When battery become weak, the operating distance of the Remote Control is greatly reduced
RANDOM
and you will need to replace the battery.
NOTE:
If the Remote Control is not to be used for a long time, remove the battery to avoid damage
caused by battery leakage corrosion.
CLEANING THE UNIT
SKIP/SEARCH buttons
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
IMPORTANT NOTICE:
• Should the CD door be opened before the reading of the CD is completed, a jamming noise may occur.
This can be resolved by closing the CD door and then press TUNER button temporarily to RADIO.
• If an abnormal display indication or an operating problem occurs, disconnect the AC power cord. Wait at
SKIP/SEARCH buttons
least 5 seconds, then reconnect the AC power cord.
• Before transporting the unit, remove the disc from the CD tray.
3. Press
MEMORY button again.
CD
MEMORY
MEMORY
4. Repeat
steps 2 and 3 to program
/
SKIP
additional tracks. After you finish program
procedure, the memory indicator will blink
on the display. Press
PLAY/PAUSE
button to start playback and memory
indicator will appear on the display.
MEMORY
To play the programmed tracks
Press
PLAY/PAUSE button.
MEMORY button. The
To stop programmed play
Press
STOP button. If you want to recover
the playback of programmed tracks, you can
first press
MEMORY button and then press
PLAY button again.
To clear the memory content
Press
STOP button and then open the CD
door or press
MEMORY button and then
press
STOP button in stop mode.
CD
REPEAT
-8-
2. Insert one CR2025 (3V) size battery.
MAINTENANCE
CLEANING CD
If the CD skips or will not play, the disc may need cleaning.
Before playing, wipe the disc from the center out with a cleaning
cloth. After playing, store the disc in its case.
-10-
VERTICAL CD MICRO SYSTEM
WITH RADIO
OPERATING INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE
WARNING
SHOCK HAZARD DO NOT OPEN
AVIS
RISQUE DE CHOC ÉLECTRIQUE NE PAS OUVRIR
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
INVISIBLE LASER RADIATION
This product contains a low
WHEN OPEN AND INTERLOCKS
power laser device.
DEFEATED.
AVOID EXPOSURE TO BEAM
TROUBLE SHOOTING GUIDE
PROBLEMS
ITEMS TO CHECK
CD
System does not turn on
• Make sure AC power plug is secure in the outlet, and
outlet has power.
Disc in place but unit won't play
• Make sure FUNCTION button is set to CD.
• Make sure disc label is facing up.
• Make sure disc is clean.
• Pause mode is activated.
Disc skips
• Disc may be damaged or dirty; check disc.
• Make sure the unit is on a secure spot. Vibration or jarring
can cause the disc to skip.
RADIO
Poor FM reception
• Make sure FM antenna wire is unwound.
• Electrical interference in your home can cause poor
reception. Move the unit away from sources of
interference (especially those with motors and
transformers).
Poor AM reception
• Set the AM loop antenna to a direction for the better
reception.
Power consumption:
40 W
Power source:
AC ~ 120V 60 Hz (USA and Canada)
AC ~ 220V 50 Hz (China)
AC ~ 230V 50 Hz (Europe and Hong Kong)
AC ~ 240V 50 Hz (Australia)
AC ~ 110-120V/220-240V 50/60Hz (Others)
Specifications subject to changed without notice.
Printed in China
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
PRODUTO LASER CLASSE 1
PRODUKT DER LASERKLASSE 1
KLASSE 1 LASER PRODUCT
APARELHO LASER DE CLASSE 1
SPECIFICATIONS
811-330391-081
Advertisement
