Related Manuals for Intertek 42193
Summary of Contents for Intertek 42193
- Page 1 52” CEILING FAN Owner’s Manual Model #42193 Item #0900852 To obtain service, please contact the Service Department: , 8 a.m. - 5 p.m. Central, Monday - Friday. 1-877-706-3267 9655 • 050120...
- Page 2 PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: PACKAGE CONTENTS 1. Canopy 12. Fitter Plate 2. Canopy Cover 13. Fitter Plate Screw (x3) 14. Light Pan 3. Mounting Bracket Screw (x4) 15. Light Pan Screw (x3) 4.
-
Page 3: Mounting Options
DIMENSION REFERENCE A. 16.02 in. B. 8.55 in. C. 8.24 in. D. 5.13 in. MOUNTING OPTIONS Two Mounting Options Downrod Mount Angled Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included). - Page 4 SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan.
- Page 5 SAFETY INSTRUCTIONS WARNING: To avoid risk of electric shock, be sure to shut off power at the main fuse or circuit breaker box before installing or servicing this fixture. Turning off the electrical power by using the light switch is not sufficient to prevent electrical shock.
- Page 6 ASSEMBLY INSTRUCTIONS 1.Turn OFF the electrical power at the main fuse or circuit breaker. DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. Mounting 2. Remove the mounting bracket by removing the two Bracket Screw mounting bracket screws from the round holes in the canopy.
- Page 7 ASSEMBLY INSTRUCTIONS 5. Feed the wires coming from the yoke through the yoke cover, canopy and downrod. Canopy Yoke Cover Downrod Yoke 6. Insert the downrod into the yoke and reinstall the downrod pin and downrod clip. Then retighten the two set screws.
- Page 8 ASSEMBLY INSTRUCTIONS 8. Use wire connectors to connect the fan wires to the Black (Hot) power supply wires according to the wiring diagram and White (Neutral) the following instructions: Bare/Green (Ground) • Connect the white wire from the fan to the white (neutral) supply wire.
- Page 9 ASSEMBLY INSTRUCTIONS 12. Remove one of the three fitter plate screws preassembled to the fitter plate from the round hole and loosen the other two but do not remove. Align the slotted holes in the light pan with the loosened screws in Fitter Plate the fitter plate.
- Page 10 ASSEMBLY INSTRUCTIONS 16. Attach pull chain extensions to the pull chains. Note: The pull chain in the center of the light kit controls the light. Installation is complete. Turn ON the electrical power at the main fuse or circuit Fan Pull breaker.
-
Page 11: Troubleshooting
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in , 8 a.m. -
Page 12: Limited Lifetime Warranty
1-877-706-3267 Model Name: 52” Ceiling Fan Model No: 42193 Set forth below, the manufacturer, Hong Kong China Electric appliance Company (HKC) warrants the fan motor for this ceiling fan to be free from defects in workmanship and material for the life of the product.