Advertisement

Quick Links

ACRYLIC SHOWER TRAYS
Installation and User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ACRYLIC SHOWER TRAYS and is the answer not in the manual?

Questions and answers

Summary of Contents for VITRA ACRYLIC SHOWER TRAYS

  • Page 1 ACRYLIC SHOWER TRAYS Installation and User Manual...
  • Page 2: Table Of Contents

    41420 Çayırova / Kocaeli Tel : 0212 350 80 00 Tel : (0262) 648 95 00 (Pbx) Faks : 0212 350 85 80 Faks : (0262) 658 85 94 www.vitra.com.tr This user manual applies to all VitrA Acrylic Shower Tray Models. October 2016...
  • Page 3: Foreword

    • In places where we do not have a seller, you may get the necessary information from the telephone numbers given in the guide. • Ask the service personnel to display their “Vitra Artema Authorized Service Personnel Card”. Do not let people without a personnel card perform the installation •...
  • Page 4: General Characteristics Of The Product

    The highest quality polymethylacrylate, in other words, "Acrylic" is used as the primary material in the production of VitrA Acrylic Shower Trays. Acrylic which has a high wear resistance is preferred because it can be easily cleaned and does not host microorganisms.
  • Page 5: Shower Tray Installation

    INSTALLATION OF SHOWER TRAYS Points that Require Attention: • Because of the technical properties of the products, the installation of shower trays were classified into four methods and explained in the following order: 1. Installation of Shower Trays with Panels 2.
  • Page 6: Installation Of Flat Shower Trays And Shower Trays For Disabled

    13- For rectangular shower trays, first the side panel and later the front panel are installed to the shower tray. For corner shower tray panels, fixed metal clips are available for panel installation under the front side rims of the shower tray to fix the panel. The panel’s installation is started from one corner by attaching the top band of the panel to these clips.
  • Page 7: Installation Of Profile Legs For Flat Shower Trays

    Installation of Profile Leg Set for Flat Shower Trays 1- Install the plastic foot to the leg, as shown in the picture, using the two nuts. Let it stay loose. 2- Install the support shaft to the leg, as shown in the picture, using the two nuts. Let it stay loose. 3- Using the markings, adjust the leg as shown in the picture, leaving 2-3mm gap between the product’s edge and the leg.
  • Page 8: Installation Of Monoblock Shower Trays

    Installation of Flat Shower Trays 1- The shower tray is placed in the installation area the levelness of which should be checked with a scale. The protective folio is removed from the sides touching the wall and from around the siphon (Note: The remaining protective folio on the shower tray should be removed only alter the installation of the shower tray and all other construction work in the bathroom are completed).
  • Page 9 9- Perform plastering correction adjustment without leaving any gap between the waterproof membrane and the wall. 10- Glue the waterproof membrane fixated to the shower tray to the f1oor from the front and rear sides with the ceramic adhesive. Perform plastering correction adjustment without leaving any gap between the waterproof membrane and the wall. 11- In the application of zero to surface shower trays, the wall tiles are laid down by leaving a jointing space from the sides of the shower tray.
  • Page 10: Maintenance Of Shower Trays

    If your problems persist please contact the nearest VitrA-Artema Authorized Service. Cleaning the Acrylic Shower Trays • Right after you use your shower tray, clean it with a liquid bath cleaner or a decalcifier and a soft cloth and warm water.
  • Page 11: Matters Not Covered Under Warranty

    DEFECTS NOT COVERED UNDER WARRANTY Shipping, Storage 1- Deformations to the product surface during the shipping and transportation carried out after the products are delivered or any breakages which may occur as the result of impacts, 2- Deformations and breakages on the surfaces of products which remain at the construction site for a long time without protection, 3- Damage to the product as the result of effects of the water and/or humidity in the environment during the storage and use of the products,...

Table of Contents