Web connect device for use with aqualink rs for systems with rev r firmware or later for use with pda for systems with 6.0 firmware or later (16 pages)
Page 1
Instructions for installation and use English H0412400.A - 2013/02...
Page 2
• Read this notice carefully before installing, maintaining or repairing this appliance! • The symbol indicates important information that it is imperative to take into consideration in order to avoid all risks of harm to persons or damage to the appliance. •...
Summary 1. Information before installing ......................3 1.1 General delivery terms and conditions ....................3 1.2 Contents ................................ 3 1.3 Technical specifications ..........................3 2. Installation ..............................3 2.1 Preparing the pool: water balance ....................... 3 2.2 Installing the control box .........................
2.1 Preparing the pool: water balance The TRi® is designed to disinfect pool water using its salt water chlorination function. It is essential that the pool water balance is controlled and adjusted before installing the appliance. Making sure that the pool water balance is correct from the very start will reduce the likelihood of encountering problems on the first days of operation or during the season the pool is in use.
• TRi® cell installed on a by-pass: the flow controller must be installed on the cell by-pass between the upstream isolation valve and the cell itself. • TRi® cell installed in line: the flow controller must be installed just in front of the cell and after a possible valve. H0412400.A - EN - 2013-02...
2.5.2 Connection to an electric roll-on shutter If the pool is fitted with an electric roll-on shutter, it can be connected to the TRi® chlorinator so that the latter automati- cally adapts its chlorine production when the shutter is closed (see §3.1.2).
Page 7
• Once the TRi® is connected to an automation system it will only be possible to access its menu via its control panel. The modification of all chlorine production related settings will from now on be managed using the au- tomation system user interfaces.
• When the «Boost» mode is acti vated, the rated chlorine producti on setti ngs are temporarily overridden and the TRi® chlorinator will operate for a total of 24 hours at a 100% chlorine producti on level. The number of days will then depend on the TRi®...
TRi® is stopped, • if the TRi® is connected to an automati on system but is not connected to a roll-on shutt er («Low» mode is then driven from the automati on system user interface). 3.2 Setti ngs 3.2.1 Clock Menu...
Page 10
The TRi® chlorinator is fi tt ed with a safety device to prevent chlorine overproducti on. It switches off the ap- pliance aft er 30 hours of conti nuous chlorinati on (no «Timers(s)» memorised and fi ltering in conti nuous mode (manual mode)).
The TRi® is equipped with a smart polarity inversion system designed to prevent the electrode plates from scaling. However cleaning may be required in regions where the water is very hard. • Turn off the TRi® and the filtering, close the isolation valves, remove the protection cover and disconnect the cell power cable.
6. Registering the product Register your product on our website: You will be the fi rst to be informed of new Zodiac products and special off ers, You can help us to constantly improve our product quality. Australia – New Zealand www.zodiac.com.au...
Page 13
TRi18, TRi22, TRi35 TRi part numbers : W382500, W382510, W382530, W382540 Zodiac TRi series - Modules TRi module Product name ; TRi pH Module, TRi Pro Module TRi module part numbers : W197525 & W197515 Ray Hin Daryl White Engineering Manager...
Page 14
Votre revendeur / your retailer Pour plus de renseignements, merci de contacter votre revendeur. For further information, please contact your retailer. ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license.