Advertisement
Quick Links
Owners Manual
'Electric Drive Operation'
ORIGINAL INSTRUCTIONS
Head Office:
P.O. Box 2018
Hilton Highway, Washdyke
Timaru, New Zealand
Telephone (03) 688 2029
Facsimile (03) 688 2821
AS3000/AS3500/DD30
Australian Branch:
4B Silverton Close
Laverton North 3026
Melbourne, Australia
Telephone (03) 9314-9666
Facsimile (03) 9314-6810
Pt. No. 67405
Issue 1113
Advertisement
Related Manuals for Duncan AS3000
Summary of Contents for Duncan AS3000
- Page 1 Owners Manual AS3000/AS3500/DD30 ‘Electric Drive Operation’ ORIGINAL INSTRUCTIONS Head Office: Australian Branch: P.O. Box 2018 4B Silverton Close Hilton Highway, Washdyke Laverton North 3026 Timaru, New Zealand Melbourne, Australia Pt. No. 67405 Telephone (03) 688 2029 Telephone (03) 9314-9666 Issue 1113...
- Page 3 Page Renovator AS3000/3500 Contents Introduction ........
-
Page 4: Acquisition & Warranty
The Owner’s Manual without notification. Your new Duncan Renovator AS3000/3500 will give long and The Company will not be efficient service if given normal care and operated properly. responsible for any damage or consequential loss arising out of This owner’s manual is provided so that you can become... -
Page 5: Description Of Machine
Description of Machine The Duncan ‘Renovator AS3000/3500’ is a Coil Tine T- boot drill. The large split hopper is mounted on a robust frame accommodating large diameter tyres. Sowing depth is controlled by adjusting the hydraulic ram as required. The quality European air metering units handle all seeds from turnip and rape through to peas and maize and permits easy calibration. -
Page 6: Read Before Operation
‘Renovator AS3000/3500’ Read Before Operation Components Referred to in the Pre-Calibration Setup and Calibration Process The following pages describe how to set the machine up for calibration, the calibration process and subsequent adjustments to obtain the desired seed and/or fertilizer output. - Page 7 ‘Renovator AS3000/3500’ Read Before Operation Components Referred to in the Pre-Calibration Setup and Calibration Process The following pages describe how to set the machine up for calibration, the calibration process and subsequent adjustments to obtain the desired seed and/or fertilizer output.
- Page 8 ‘Renovator AS3000/3500’ Read Before Operation Components Referred to in the Pre-Calibration Setup and Calibration Process The following pages describe how to set the machine up for calibration, the calibration process and subsequent adjustments to obtain the desired seed and/or fertilizer output.
- Page 9 ‘Renovator AS3000/3500’ Read Before Operation Components Referred to in the Pre-Calibration Setup and Calibration Process The following pages describe how to set the machine up for calibration, the calibration process and subsequent adjustments to obtain the desired seed and/or fertilizer output.
- Page 10 ‘Renovator AS3000/3500’ Read Before Operation...
- Page 11 ‘Renovator AS3000/3500’ Pre-Calibration Setup normal/fi ne toggle Start Empty boxes and clear old seed and fertilizer from metering unit. high (idler in) low (idler out) Is seed size between 4 and 10mm? Locate product in 'Normal' Locate product in 'Fine' seed seed table.
- Page 12 ‘Renovator AS3000/3500’ Calibration Calibration The calibration test should be done to confirm the settings of the required seed rate and is done with the drill stationary and level with the fan off. The metering units must be set prior to filling with seed and the bins are calibrated one-at-a-time.
- Page 13 ‘Renovator AS3000/3500’ Calibration Calibration via PRIMING SWITCH (continued) The appropriate metering unit will run until the PRIMING SWITCH is pressed again. Product is collected in this time. The operator is in control of the amount of product metered out so is able to stop the metering unit when the collecting container is at a suitable fill level.
- Page 14 ‘Renovator AS3000/3500’ Calibration (ii) Calibration via ‘SETUP’ MENU Ensure that steps 1 to 8 at the top of page 21 have been carried out prior to actual calibration. Navigate to the ‘SETUP’ screen by pressing the ‘SETUP’ key. Access the ‘Calibration Check’ screen by hitting the key below the weighing scales icon.
- Page 15 ‘Renovator AS3000/3500’ Calibration (ii) Calibration via ‘SETUP’ MENU continued NOTE: If, when presing the priming switch the motors do not turn but there are no other errors, it could be that the previous calibration was wrongly entered. The metering speed is out of the range of the motor speed.
- Page 16 ‘Enviro DD30’ Sowing Chart Normal...
- Page 17 ‘Enviro DD30’ Sowing Chart Fine FINE SEED (toggle ‘FINE’, Butterfl y Valve Settings shown below and on page 22) SPECIFIC Setting PRODUCT GRAVITY (kg/l) Position> 2.5 12.5 17.5 22.5 RATE ONCE SET DO NOT REDUCE/CLOSE WITH SEED IN BIN** Lucerne (Alfalfa) 0.77 1.10 3.06 4.60 6.49 7.93 9.34 11.28 12.95 14.39 15.50 Turnip...
-
Page 18: Airflow & Fan Speed
‘Renovator AS3000/3500’ Airflow & Fan Speed Airflow and Fan Settings The return hose for the hydraulic fan must only be connected to the tractor’s low pressure return circuit. If this is not carried out, the hydraulic motor seals will fail. - Page 19 ‘Renovator AS3000/3500’ Calibration Notes Pt. No. 67405 Issue 1113...
- Page 20 • • • • • • • • • • • • • • • • • • • •...
- Page 21 • • • • • • • • • • • • • • • • • • • • Pt. No. 67404 Issue 1113...
- Page 22 • • • • • • • • • • • • • • • •...
- Page 23 • • • • • • • • • • • • • • • • • • • • • • • • • Pt. No. 67404 Issue 1113...
- Page 24 • • • • • • • • • • • • • • • • • • •...
- Page 25 • • • • • • • • • • • • • • • • • Pt. No. 67404 Issue 1113...
- Page 26 • • • • • • • •...
- Page 27 Renovator DC-AS5000-1 Notes Pt. No. 67405 Issue 1113...
Need help?
Do you have a question about the AS3000 and is the answer not in the manual?
Questions and answers