Prestan Adult Manikin 2000 Series Troubleshooting Manual

SYMPTOM

CPR MONITOR

SYMPTOM
CPR Monitor lights
CPR MONITOR
are not working
properly
CPR Monitor lights
are not working
To help understand how
properly
the CPR Monitor works,
please note that the CPR
To help understand how
Monitor lights are
the CPR Monitor works,
powered by a small
please note that the CPR
current generated by the
Monitor lights are
CPR Monitor
powered by a small
current generated by the
Please follow the
CPR Monitor
troubleshooting tips at
right in the order they
Please follow the
are listed for best
troubleshooting tips at
results
right in the order they
CPR Monitor lights are
are listed for best
all on
results
CPR Monitor lights are
CPR Monitor red
all on
light is blinking
CPR Monitor red
light is blinking
Manikin Torso And Face-Shield/Lung-Bag
Cannot hear a beep
MANIKIN TORSO AND FACE-SHIELD/LUNG-BAG
when doing
compressions
Cannot hear a beep
when doing
compressions
PRESTAN Professional Adult Series 2000 Manikin
TROUBLESHOOTING GUIDE
POSSIBLE ISSUES OR COMMENTS
POSSIBLE ISSUES OR COMMENTS
•
Chest compressions are not deep
enough to signal CPR Monitor
•
Batteries are not installed, need
•
Chest compressions are not deep
replacing
enough to signal CPR Monitor
correctly in the CPR Monitor
•
Batteries are not installed, need
•
CPR Monitor may be clogged with
replacing or are
plastic dust, interrupting the signal
correctly in the CPR Monitor
to the Monitor
•
CPR Monitor may be clogged with
•
CPR Monitor needs to be replaced
plastic dust, interrupting the signal
to the Monitor
•
CPR Monitor needs to be replaced
• Batteries are running low
• Batteries are running low
• This is normal after replacing batteries,
manikin is paused or is connecting to
CPR Feedback app ‐ may blink up to 10
• This is normal after replacing batteries,
minutes to indicate ready status
manikin is paused or is connecting to
CPR Feedback app ‐ may blink up to 10
minutes to indicate ready status
•
Hand position and/or compression
angle may be incorrect
•
Compressions may not be deep
•
Hand position and/or compression
enough to activate the CPR Monitor
angle may be incorrect
•
CPR Monitor may be broken
•
Compressions may not be deep
•
enough to activate the CPR Monitor
Batteries
misassembled
•
CPR Monitor may be broken
•
Batteries may
misassembled
•
or are not inserted
•
not inserted
•
•
•
•
•
•
may be dead or
•
be dead or
1
SOLUTIONS
SOLUTIONS
•
Compress the chest until the beep is
audible from the CPR Monitor at 2"‐
2.4"
Compress the chest until the beep is
•
Install or replace batteries into CPR
audible from the CPR Monitor at 2"‐
Monitor (back of manikin, left
2.4"
shoulder area) ‐ requires 2‐AA (1.5V)
Install or replace batteries into CPR
batteries
Monitor (back of manikin, left
•
Remove CPR Monitor and blow out
shoulder area) ‐ requires 2‐AA (1.5V)
dust – then replace CPR Monitor and
batteries
reconnect
Remove CPR Monitor and blow out
•
Exchange CPR Monitor with working
dust – then replace CPR Monitor and
manikins (if available) to determine if
reconnect
CPR Monitor needs to be replaced
Exchange CPR Monitor with working
manikins (if available) to determine if
CPR Monitor needs to be replaced
•
Replace batteries
Replace batteries
•
Commence or resume compressions ‐
blinking will stop and feedback rate
signals will begin
Commence or resume compressions ‐
blinking will stop and feedback rate
signals will begin
•
Confirm correct hand placement and
compress straight down from directly
above the manikin
Confirm correct hand placement and
•
Compress between 2 and 2.4 inches
compress straight down from directly
depth
above the manikin
•
Replace batteries
Compress between 2 and 2.4 inches
depth
Replace batteries