Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Skandia Elevator L Series
Summary of Contents for Skandia Elevator L Series
- Page 1 ASSEMBLY INSTRUCTIONS L-LINE...
- Page 3 Warranty A 2-year factory warranty from the day of delivery applies to all models of Skandia Elevator AB machinery. A condition of the warranty and any subsequent compensation is that Skandia Elevator AB is contacted and an agreement reached between the customer and Skandia Elevator AB on how any faults should be rectified.
-
Page 5: Table Of Contents
Contents Thank you for choosing Skandia Elevator! Your conveyor system must be assembled correctly and maintained thoroughly if it is to operate satisfactorily. These assembly instructions and the separate maintenance instructions must be followed for the warranty to apply. We hope you will be pleased with your Skandia conveyor equipment for a long time. -
Page 7: Machine Overview
Machine overview DEK3040 DEK3030 DEK3030 Parts Pos.. Tail end Trench intake section Bend section Drive Motor Transmission with guard Outlet Safety decals X X X X SKANDIA ELEVATOR –KTG... -
Page 8: Safety Information
• Use protective gloves, helmet, steel-toed boots, ear defenders, protective goggles and high-vis vest when carrying out assembly, electrical connection, maintenance and operation of conveyor equipment. SKANDIA ELEVATOR – KTG... -
Page 9: General Safety Information
Inadequate maintenance may lead to personal injury or damage to the conveyor equipment and/or other equipment. It can also cause malfunctions or a reduction in capacity. WARNING! Read the separate maintenance instructions before taking the machine into service. SKANDIA ELEVATOR –KTG... -
Page 10: Electrical Safety
The machine is supplied with safety decals on delivery. They must not be removed or defaced. If a safety decal becomes damaged, you can order a new one free of charge from Skandia Elevator AB. Specify the part number of the decal. See the section below and the previous chapter Machine Overview. - Page 11 Warning for chain drive! DEK3040 SKANDIA ELEVATOR – DEK3040 DEK3050 Warning for belt drive! SKANDIA ELEVATOR – DEK3050 DEK3070 Warning for rotating conveyor drive shaft! SKANDIA ELEVATOR – DEK3070 DEK3080 Warning for rotating elevator drive shaft! SKANDIA ELEVATOR – DEK3080...
-
Page 12: Before Assembly
Illustration A shows: Trench intake section and drive assembled directly to the bend section. Illustration B shows: Intermediate section assembled partly between trench intake section and bend section, partly between bend section and drive. SKANDIA ELEVATOR – KTG... - Page 13 SKANDIA ELEVATOR –KTG...
-
Page 14: Construction Dimensions For Inclined Conveyors
52.3 13.4 20.8 34.6 18.1 17.6 14.5 34.6 48.5 69.3 Max. X2+X3 = 242.5 45° 78.5 70.7 29.3 16.9 16.9 28.3 28.3 14.2 11.9 11.9 28.3 28.3 39.6 39.6 56.5 56.5 Max. X2+X3 = 141.4 141.4 SKANDIA ELEVATOR – KTG... - Page 15 α 15° 1000 1000 1400 1352 2000 1932 Max. X2+X3 = 13600 13136 3520 30° 1309 1250 1000 1000 1400 1212 2000 1732 1000 Max. X2+X3 = 7000 6062 3500 45° 1963 1768 1000 1000 1400 2000 1414 1414 Max. X2+X3 = 5000 3535 3535...
-
Page 16: Connection Of The Machine
• The connection between the trench intake section and the intake pit must be permanently mounted and enclosed. • The intake pit must be installed with a permanent protective grating IMPORTANT! The full weight of the intake pit must never rest on the conveyor. SKANDIA ELEVATOR – KTG... -
Page 17: Connection To Following Machine
Connection to following machine Connect the conveyor to the following machine according to its assembly instructions. SKANDIA ELEVATOR –KTG... -
Page 18: Assembling The Machine
Illustration A shows: Trench intake section and drive assembled directly to the bend section. Illustration B shows: Intermediate section assembled partly between trench intake section and bend section, partly between bend section and drive. SKANDIA ELEVATOR – KTG... - Page 19 SKANDIA ELEVATOR –KTG...
- Page 20 Note! The chain brackets "push" the flights against the drive. Note! Use a rope to pull the chain through the bend. Install the intermediate trays from the bend and outwards. IMPORTANT! Install the finger joints together correctly. SKANDIA ELEVATOR – KTG...
- Page 21 Position the conveyor chain over the tail end's chain sprocket. Shorten it to the correct length if necessary, and then assemble it. IMPORTANT! Make sure that the conveyor chain is centered, runs freely, and does not foul the sides of the conveyor. SKANDIA ELEVATOR –KTG...
- Page 22 A new conveyor chain must be run for a period of time and then readjusted. IMPORTANT! Check the conveyor chain after 50 operating hours. See the separate maintenance instructions for information on maintenance. SKANDIA ELEVATOR – KTG...
- Page 23 SKANDIA ELEVATOR –KTG...
- Page 24 Note! Use the joining plate to cover seams in the lid that do not overlap. IMPORTANT! • Install rubber gaskets in the joint grooves. • When assembling outdoors, the seams in the side plates, lid, and inlet must be sealed with silicone. SKANDIA ELEVATOR – KTG...
- Page 25 (and power shuts off) at actual overfill or deliberate opening. WARNING! • Ensure the safety switch for the pop up overloading flap is engaged during operation. • All electrical equipment must be connected by a qualified electrician. See separate connecting directions for electronics. SKANDIA ELEVATOR –KTG...
-
Page 26: Assembling The Motor
Adjust the tightness of the transmission chains continuously. For more information concerning the transmission chain, see the separate maintenance instructions. The transmission guard (D) is hooked on at the bottom and fastened with two bolts at the top. SKANDIA ELEVATOR – KTG... - Page 27 SKANDIA ELEVATOR –KTG...
- Page 28 SKANDIA ELEVATOR AB KEDUMSVÄGEN 14, ARENTORP PHONE +46 (0)512 79 70 00 INFO@SKANDIAELEVATOR.COM S-534 94 VARA, SWEDEN FAX +46 (0)512 134 00 WWW.SKANDIAELEVATOR.COM...
Need help?
Do you have a question about the L Series and is the answer not in the manual?
Questions and answers