Related Manuals for HYDAC International CS 2000 Series
Summary of Contents for HYDAC International CS 2000 Series
- Page 1 Fluid Sampling Set Operating and Maintenance Instructions English (translation of original instructions) Document No.: 3160266a...
-
Page 2: Trademarks
Fluid Sampling Set - FES Trademarks Trademarks The trademarks of other companies are exclusively used for the products of those companies. Copyright © 2008 by HYDAC Filtertechnik GmbH all rights reserved All rights reserved. This manual may not be reproduced in part or whole without the explicit written agreement from HYDAC Filtertechnik. -
Page 3: Table Of Contents
Fluid Sampling Set - FES Contents Contents Trademarks ..........................2 Contents..........................3 Preface ............................ 4 Customer Service ......................... 5 Modifications to the Product ....................5 Warranty ..........................5 Using the documentation ...................... 6 Safety Information and Instructions..................7 Explanation of Symbols and Warnings ................. 7 Please observe the instructions in this manual.............. -
Page 4: Preface
Fluid Sampling Set - FES Preface Preface For you, as the owner of a product manufactured by us, we have produced this manual, comprising the most important instructions for its operation and maintenance. It will acquaint you with the product and assist you in using it as intended in an optimal manner. -
Page 5: Customer Service
Fluid Sampling Set - FES Preface Customer Service Contact our technical sales department if you have any questions on our product. When contacting us, please always include the model/type designation, serial no. and part-no. of the product: Fax: ++49 (0) 6897 509 846 Email: filtersysteme@hydac.com Modifications to the Product We would like to point out that changes to the product (e.g. -
Page 6: Using The Documentation
Fluid Sampling Set - FES Preface Using the documentation Note that the method described for locating specific information does not release you from your responsibility of carefully reading these instructions prior to starting the unit up for the first time and at regular intervals in the future. -
Page 7: Safety Information And Instructions
Fluid Sampling Set - FES Safety Information and Instructions Safety Information and Instructions Explanation of Symbols and Warnings The following designations and symbols are used in this manual to designate hazards, etc.: DANGER denotes situations DANGER which can lead to death if safety precautions are not observed. -
Page 8: Hazards Posed By Using The Fes
Fluid Sampling Set - FES Safety Information and Instructions Hazards Posed by Using the FES The Fluid Sampling Set FES is made up of individual components which are designed and constructed in accordance with the technical state of the art and recognized safety rules and regulations. -
Page 9: Checking The Scope Of Delivery
Fluid Sampling Set - FES Checking the scope of delivery Checking the scope of delivery The Fluid Sampling Set FES is supplied in a ready-for-operation condition. Check the individual components for possible damage in transit before putting the FES into operation. -
Page 10: Fluid Sampling Set Properties
Fluid Sampling Set - FES Fluid Sampling Set properties Fluid Sampling Set properties Compliance with and regular monitoring of the particle load in fluid and lubrication technology is essential for efficient, economical system use. Static and dynamic sampling for later fluid analysis can be carried out using very simple means with the Fluid Sampling Set FES. -
Page 11: Oil Contaminations Influence The Ageing Of The Oil
Fluid Sampling Set - FES Fluid Sampling Set properties Oil contaminations influence the ageing of the oil Solid particles In addition to the enormous damage to hydraulic components from wear caused by solid particles, the materials of these particles also have an impact on oil aging that cannot be ignored. -
Page 12: Sampling
Fluid Sampling Set - FES Sampling Sampling NOTE The FluidAnalysis Set may only be used with mineral oils. Contact us prior to using with other operating fluids. Static sampling This procedure treats the sampling from the reservoir of a system which is not equipped with sampling valves. - Page 13 Fluid Sampling Set - FES Sampling This method involves the taking of bottle samples of hydraulic fluid from operating fluid power systems via sampling valves provided for that purpose. The sampling should be representative of the operating condition of the hydraulic system. Therefore, the samples should be taken from the same point in the system each time, to enable comparisons to be made.
-
Page 14: Labelling Samples
Fluid Sampling Set - FES Performing maintenance Labelling samples The bottle sample should be labelled with the following information: o Sample number o Machine type o Sampling method o Date and time of the sampling o Fluid type Performing maintenance The Fluid Sampling Set FES is a combination of laboratory-quality components. -
Page 15: Spare Parts List
Fluid Sampling Set - FES Spare Parts List Spare Parts List Item Article designation Part no. Hand vacuum pump with manometer 309 345 Aluminum adapter 309 349 Set of sample flasks (2 pieces) 309 352 Spray bottle with removable nozzle, 500 ml 309 358 Disposable membrane filter for spray bottle, 309 371... - Page 16 HYDAC Filtertechnik GmbH Bereich Servicetechnik / Service Technology Division Industriegebiet Postfach 1251 66280 Sulzbach/Saar 66273 Sulzbach/Saar Germany Germany Tel: +49 (0) 6897 509 01 Fax: +49 (0) 6897 509 846 (Technical Department) Fax: +49 (0) 6897 509 577 (Sales Department) Internet: www.hydac.com email: filtersysteme@hydac.com...