Advertisement
Available languages
Available languages
User Manual
Electric heating element with thermostat
Thank you for buying this product made by HeatQ Technology Sp. z o.o.
HeatQ products are designed and manufactured according to the best
practices. Read and understand this User Manual to enjoy a failure-free
operation of the product. Keep this User Manual for future reference. You can
also download a copy from: www.heatq.com
Safety precautions: Installing the electric heating
element (Fig. 2, 4)
1. Install the electric heating element according to this User Manual.
2. Have the electric heating element installed only by a qualified technical
professional and connected to a professionally wired electrical system
which matches the ratings of device. Consult the nameplate or the
technical specifications in the User Manual.
3. These safety precautions show the permitted installation location of the
electric heating element and the minimum distance from wet areas
(washbasins, showers and bath tubs) which must be followed to avoid
electrocution.
4. The type of the electrical system connected to the electric heating element
must be compliant with local electrical engineering and safety standards
and regulations.
5. The power supply line of the electric heating element must feature a 30-
milliamp overcurrent circuit breaker (integrated with a ground fault
breaker).
6. Do not connect the electric heating element to live voltage through any
extension cords or adapters.
7. If the electric heating element is wired to the power supply through a
circuit breaker which breaks all poles for a complete isolation from
voltage or without a power cord plug removable from a mains outlet,
install this circuit breaker in the building's electrical supply line connected
to the electric heating element in compliance with applicable electrical
engineering and safety standards and regulations.
8. Do not power on the electric heating element when dry (outside a heating
radiator primed with a heating medium) for more than 2 seconds.
9. Do not use the electric heating element in a system the heating medium
temperature of which can exceed 82°C, otherwise the overtemperature
trip may fail.
10. Make sure that the power supply line connected to the electric heating
element does not touch any hot surface of the device or its heating
radiator.
11. Never attempt to power on the electric heating element with its heating
radiator empty!
12. The maximum operating pressure of the heater radiator is 10 Atm.
13. The power output of the electric heating element must be equal to or
less than the power output of its heating radiator operated at
75/65/20°C.
14. Always isolate the electric heating element from live voltage before
installing or removing it.
15. This electric heating element is intended for domestic non-commercial
use only.
Safety precautions: Operating the electric
heating element
1. Use this electric heating element only as intended by the manufacturer.
2. This electric heating element is not a toy. Keep it out of the reach of
children.
3. Frequently inspect the electric heating element to assure its continued
safe use.
4. If the permanent power cord is damaged, do not use the electric heating
element. Isolate it from the supply voltage. Have the damaged power
cord replaced by the manufacturer or a qualified service professional to
avoid hazards to health and life.
5. The manufacturer shall not be liable for any consequences of unauthorized
tampering with the microchip controller internals or any unauthorized
modification of the design of the electric heating element.
6. Protect the electric heating element controller from flooding.
7. This device can be operated by children at least 8 years old, the physically
and/or mentally challenged, and people inexperienced in and/or
unfamiliar with this product type only when supervised and/or instructed
by able and responsible adults to make the safe use and potential
hazards of operation clearly understood. Do not let children play with the
device. Do not allow children to clean or maintain the electric heating
element unsupervised.
8. Clean the device when isolated from live voltage.
9. The electric heating element and its heating radiator can become hot to
touch when in use: hazard of burns!
Security requirements - electric radiator/towel
warmer (Fig. 2, 3, 8, 9)
Safe installation and operating procedures: Informative
1. Use the device as intended by the manufacturer.
2. The electric radiator is not a toy. Keep it out of the reach of children.
3. Install the electric radiator on a wall according to the instructions from
its manufacturer.
4. To maximize safety to small children, install the electric radiator with
the bottom edge at least 60cm above the floor.
5. The electric heater can become very hot: hazard of burns! Extreme
caution is advised when operating the electric radiator in presence of
children and the physically and/or mentally challenged.
6. When drying towels or clothes, make sure that the laundering products
and the textiles can be exposed to drying at high temperatures.
7. Do not connect the device to live voltage through any extension cords
or adapters.
8. Have the equipment installed by a qualified professional and in
compliance with applicable safety standards and regulations. All
electrical power systems the equipment is connected to must meet the
local engineering and safety standards and regulation.
9. The power supply line of the device must feature a 30-milliamp
overcurrent circuit breaker (integrated with a ground fault breaker).
10. If the device is wired to the power supply through a circuit breaker
which breaks all poles for a complete isolation from voltage or without
a power cord plug removable from a mains outlet, install this circuit
breaker in the building's electrical supply line connected to the device
in compliance with applicable electrical engineering and safety
standards and regulations.
Intended use
(Fig. 1, 6, 7)
This electric heating element when properly chosen and sized for your
application, is a heating device and a component of a radiator. Install the
heating element in a radiator (a standalone unit or connected to a central
heating system) to provide it with a functionality of a laundry dryer.
This electric heating element does not feature an indoor room thermostat
for temperature control.
Technical specifications
Type:
NORD1.0
Power supply ratings:
~230VAC, 50Hz
Insulation class:
I
Power rating:
120, 200, 300, 400, 500, 600, 800,
1000, 1200W
Enclosure IP rating:
IPx4
Electrical supply connection type: Y (The power cord is non-user
replaceable and shall only be serviced
by the manufacturer.)
Permanent wiring to the electrical
supply system
Threaded connection port:
1/2"
Design overview (Fig. 1)
1. Heating element
2. Controller housing
3. Knob for selecting functions and temperature settings
4. Colorful display
5. Suppling cable: NORD1.0.A - straight cable with the plug
NORD1.0.B - spiral cable with the plug
NORD1.0.C - masking cable
Installation instructions
(Fig. 2, 3, 4, 5, 6, 7, 8, 9)
Before attempting the installation, make sure that the electric heating
element is isolated from the mains. Do not power on the electric heating
element when dry: hazard of burns and failure of the overtemperature
trip! Make sure that the heating radiator has water (or another liquid
heating medium, as applicable), before powering on the electric heating
element.
English
- 7 -
Advertisement
