Table of Contents
Advertisement
Quick Links
Zero Clearance Direct Flue Gas Fireplace
STYLE
Left Corner
Right Corner
Warning
Fire or explosion Hazard
failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Installer: Please complete the details on the back cover and leave this manual with the homeowner.
920-124
City Series
MODEL
ACC40LENG / ACC40LELP / ACC40LEULPG
ACC40RENG / ACC40RELP / ACC40REULPG
Homeowner: Please keep these instructions for future reference.
®
Owners &
Installation Manual
LISTINGS AND CODE APPROVALS
These gas appliances have been
tested in accordance with AS/NZS
5263.0 & AS/NZS 5263.1.8:2016
and have been certified by IAPMO
for installation and operation as
described in these Installation and
Operating Instructions.
Must be installed as per AS/NZS5601.
Your unit should be serviced
annually by an authorised service
person.
www.regency-fire.com.au
PRIMARILY A DECORATIVE AND NOT A
HEATING APPLIANCE.
DO NOT MODIFY THIS APPLIANCE.
03.12.20
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Regency ACC40LENG
Summary of Contents for Regency ACC40LENG
- Page 1 Your unit should be serviced annually by an authorised service person. www.regency-fire.com.au STYLE MODEL Left Corner ACC40LENG / ACC40LELP / ACC40LEULPG Right Corner ACC40RENG / ACC40RELP / ACC40REULPG Warning PRIMARILY A DECORATIVE AND NOT A Fire or explosion Hazard HEATING APPLIANCE.
-
Page 2: Data Badge
NOTE: Regency ® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. Copy of Data Badge Regency Gas Fireplace Distributed by: Propane ULPG... - Page 3 dimensions Dimensions (Left Corner) 1203mm 616mm 587mm 102mm 172mm 1219mm 475mm 449mm 1109mm 1089mm 375mm Note: Height Dimension may vary depending on the height of the leveling legs. Note: These units are non-load bearing. ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.
- Page 4 dimensions Dimensions (Right Corner) 1203mm 587mm 616mm 102mm 172mm 475mm 448mm 1108mm 374mm 1091mm Note: Height Dimension may vary depending on the height of the leveling legs. Note: These units are non-load bearing. | City Series ACC40E...
-
Page 5: Installation
installation Clearances The clearances listed below are Minimum distances unless otherwise stated: A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fireplace and flue system be installed only in accordance with these instructions. Note: ACC40LE shown in illustration. - Page 6 installation Clearances Lo w framing with vents Low framing with vents in front/sides or top ACC40LE shown Floor to ceiling with top op Floor to ceiling with top opening ACC40LE shown | City Series ACC40E...
- Page 7 installation Clearances Chase enclosed ACC40LE shown Full framing with low vents in front or sides ACC40LE shown Full framing with vents in front or sides City Series ACC40E |...
-
Page 8: Mantel Clearances
installation Mantel Clearances Combustible mantel clearances from top of front facing are shown in the diagram on the right. 13mm Plasterboard, timber, timber panel, etc. 305mm 229mm 130mm Top of Bottomof Fireplace Fireplace Opening Opening 383mm | City Series ACC40E... - Page 9 installation Framing Dimensions (Left Corner) NOTE: Framing may be constructed of combustible material (ie. 51mm x 102mm) and does not require steel studs. Note: A combined minimum of Framing 774 square centimetres of open Description ACC40LE Dimensions area is required for the convection air outlet to cool the enclosure.
- Page 10 installation Framing Dimensions (Right corner) NOTE: Framing may be constructed of combustible material (ie. 51mm x 102mm)and does not require steel studs. Note: A combined minimum of Framing Description ACC40RE 774 square centimetres of open Dimensions area is required for the convection Framing Height 949mm air outlet to cool the enclosure.
- Page 11 installation TV Recessed Into Wall- Typical Installs Maximum TV Recess TV Flush with Hearth City Series ACC40E |...
-
Page 12: Venting Introduction
Refer to the "Flue Restrictor Position" section for details on how to change the flue restrictor from the factory setting of Set 0 to Set 2 if required. Note: For horizontal terminations the Regency Direct Flue Flex System may be used for installations with a maximum continuous flue length of up to 3m. If longer runs are required, rigid pipe must be used. -
Page 13: Horizontal Terminations
S.S. screws #8 x 38mm drill point Notes: 1. Liner sections should be continuous without any joints or seams. 2. Only Flex pipe purchased from Regency may be used ® for Flex installations 3. Horizontal vent must be supported every 0.9m. - Page 14 installation Horizontal Terminations Rigid Pipe 102mm x 175mm The minimum components required for a basic horizontal termination are: Horizontal Termination Cap Rigid Pipe Adaptor (510-994) Wall Thimble Length of pipe to suit wall thickness (see chart) Wall thickness is measured from the back standoffs to the inside mounting surface of termination cap.
- Page 15 installation Horizontal Terminations Rigid Pipe 102mm x 175mm The diagrams below show examples of horizontal termination arrangements using one, two, or three 90 elbows (two 45 elbows equal one 90 elbow) 1. A maximum of three 90 elbows are permitted. 2.
- Page 16 installation Flueing Arrangement for Vertical Terminations Vertical Flueing with Straight Vertical Flueing and or with a max. of two (2) 90 Elbows (1 - 90 2 - 45 The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using two elbows, with Rigid Pipe Flueing Systems.
-
Page 17: Vertical Terminations
installation Vertical Terminations Rigid Pipe 102mm x 175mm The minimum components required for a basic vertical termination are: Vertical Termination Cap Rigid Pipe Adaptor (510-994) Ceiling Firestop Flashing Storm Collar Length of pipe to suit wall thickness (see chart) Galvanized pipe is desirable above the roofline due to its higher corrosion resistance. - Page 18 installation Vertical Terminations Rigid Pipe 102mm x 175mm • Two 45 elbows equal to one 90 elbow. Maximum of six 45 elbows allowed. • Flue must be supported at offsets. • Minimum distance between elbows is 305mm. • Maintain clearances to combustibles as listed in the "Clearances" section. •...
Need help?
Do you have a question about the ACC40LENG and is the answer not in the manual?
Questions and answers