Hard Disk Drives - Asus Vintage AH1 User Manual

Barebone system
Hide thumbs Also See for Vintage AH1:
Table of Contents

Advertisement

3 .
3 .
3 . 3 .
3 .
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA

hard disk drives.

SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
You must install Windows
Service Pack1 before using Serial ATA hard disk drives.
When using the connectors in standard IDE mode, connect the primary
(boot) hard disk drive to the SATA1 or SATA2 connector.
4 . 4 .
4 .
4 .
4 .
C P U a n d C h a s s i s F a n c o n n e c t o r s
C P U a n d C h a s s i s F a n c o n n e c t o r s
C P U a n d C h a s s i s F a n c o n n e c t o r s
C P U a n d C h a s s i s F a n c o n n e c t o r s
C P U a n d C h a s s i s F a n c o n n e c t o r s
( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
The fan connectors support cooling fans of 350 mA~740 mA (8.88 W
max.) or a total of 1 A~2.22 A (26.64 W max.) at +12V. Connect the
fan cables to the fan connectors on the motherboard, making sure that
the black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the
fan connectors!
Fan connectors
A S U S V i n t a g e - A H 1
A S U S V i n t a g e - A H 1
A S U S V i n t a g e - A H 1
A S U S V i n t a g e - A H 1
A S U S V i n t a g e - A H 1
®
®
2000 Service Pack 4 or the Windows
CPU_FAN
CHA_FAN
®
SATA3
SATA4
SATA1
SATA2
GND
+12V
Rotation
®
XP
4 - 7
4 - 7
4 - 7
4 - 7
4 - 7

Advertisement

Table of Contents
loading

This manual is also suitable for:

Vintage-ah1

Table of Contents