Table of Contents
Advertisement
5. Electrical installation
The electrical installation and connection to power supply must be done in compliance with the existing regulations and standards for
Operation and maintenance documentation SOLANO RANGE
building industry.
The fan's engine is equipped with the internal temperature limit fuse protecting the engine from its overheating.
Operation and maintenance documentation SOLANO RANGE
The unit set does not consist of: a feeding cable, a master switch (see diagram)
5.
ELECTRICAL INSTALLATION
The electrical installation must be done by an authorised person, acquainted with the Manual. The connection of the feeding cable and
The electrical installation and connection to power supply must be done in compliance with the existing regulations and stand-
master switch must be done in compliance with electrical diagram (with or without the automatic control, depending on the option
5.
ards for building industry.
ELECTRICAL INSTALLATION
chosen). Any and all damages incurred as a result of the aforementioned causes are not provided with the Guarantee and the user will
The fan's engine is equipped with the internal temperature limit fuse protecting the engine from its overheating.
The electrical installation and connection to power supply must be done in compliance with the existing regulations and stand-
be charged with any costs of the device exchange. The connection of the automatic control should be carried out in accordance with
The unit set does not consist of: a feeding cable, a master switch (see diagram)
ards for building industry.
The electrical installation must be done by an authorized person, acquainted with the Manual. The connection of the feeding
the electrical diagram.
The fan's engine is equipped with the internal temperature limit fuse protecting the engine from its overheating.
cable and master switch must be done in compliance with electrical diagram (with or without the automatic control, depending
In case of any doubts or problems, unplug the device and contact the device's installer or Smith's Authorised Service.
The unit set does not consist of: a feeding cable, a master switch (see diagram)
on the option chosen). Any and all damages incurred as a result of the aforementioned causes are not provided with the Guar-
The electrical installation must be done by an authorized person, acquainted with the Manual. The connection of the feeding
antee and the user will be charged with any costs of the device exchange. The connection of the automatic control should be
carried out in accordance with the electrical diagram.
cable and master switch must be done in compliance with electrical diagram (with or without the automatic control, depending
6. Water installation
In case of any doubts or problems, unplug the device and contact the device's installer or SONNIGER Authorized Service.
on the option chosen). Any and all damages incurred as a result of the aforementioned causes are not provided with the Guar-
antee and the user will be charged with any costs of the device exchange. The connection of the automatic control should be
The installation of the unit should be done in a way enabling maintenance service; on both stub pipes manual closing valves should
carried out in accordance with the electrical diagram.
6.
WATER INSTALLATION
be installed in order to cut off the device. Feeding cables of the heater shall be connected in accordance with the symbols/marking on
In case of any doubts or problems, unplug the device and contact the device's installer or SONNIGER Authorized Service.
the casing (inlet/outlet). In case of electromagnetic valve (with the option of the automatic control) it should be installed on the outlet
The installation of the unit should be done in a way enabling maintenance service; on both stub pipes manual closing valves
should be installed in order to cut off the device. Feeding cables of the heater shall be connected in accordance with the sym-
as it may be damaged otherwise. When the pipework is being connected to the exchanger, secure the connections of the heater from
6.
WATER INSTALLATION
bols/marking on the casing (inlet/outlet). In case of electromagnetic valve (with the option of the automatic control) it should
oscillating torque (see figure) that may cause leakage in the exchanger.
be installed on the outlet as it may be damaged otherwise. When the pipework is being connected to the exchanger, secure the
The installation of the unit should be done in a way enabling maintenance service; on both stub pipes manual closing valves
connections of the heater from oscillating torque (see figure) that may cause leakage in the exchanger.
should be installed in order to cut off the device. Feeding cables of the heater shall be connected in accordance with the sym-
bols/marking on the casing (inlet/outlet). In case of electromagnetic valve (with the option of the automatic control) it should
be installed on the outlet as it may be damaged otherwise. When the pipework is being connected to the exchanger, secure the
connections of the heater from oscillating torque (see figure) that may cause leakage in the exchanger.
6 | SmithsEP.co.uk | Issue 001 - May 2021
Heating medium
The connector pipes are at the back of the device.
When connecting the hydraulic pipes/connections, make sure you
Heating medium
OUT
secure the connector pipes against rotational torque.
G 3/4" Eco 1, 2 & 3
The connector pipes are at the back of the
G 3/4" Eco MAX 1,
Notice that the connector pipes are not strained by the pipes.
device.
2 & 3
pipes/connections, make sure you secure the
Heating medium
The valve of heating medium is on the supply pipe and the vent is
connector pipes against rotational torque.
on the return pipe.
The connector pipes are at the back of the
Notice that the connector pipes are not
device.
strained by the pipes. The valve of heating
pipes/connections, make sure you secure the
medium is on the supply pipe and the vent is
on the return pipe.
connector pipes against rotational torque.
Notice that the connector pipes are not
strained by the pipes. The valve of heating
medium is on the supply pipe and the vent is
IN
on the return pipe.
G 3/4" Eco 1, 2 & 3
G 3/4" Eco MAX 1,
2 & 3
Use flexible connections to allow the heater to
Use flexible connections to allow the heater to be turned to the
be turned to the sides. Depending on the
flexible connections, the maximum turn
sides. Depending on the flexible connections, the maximum turn
is 70° - for HEATER CONDENS MAX,
is 70° - for Solano Eco MAX, 78° - for Solano Eco 1, 2 and 3 to
78° - for HEATER CONDENS CR1, CR2, CR3,
X = 78° Eco 1, 2 & 3
both sides. Figure shows maximum angle to one side and 50° to
Use flexible connections to allow the heater to
68° - for HEATER CONDENS ONE , to both
X = 70° Eco MAX
the other with minimal distance left for connections.
be turned to the sides. Depending on the
1, 2 & 3
sides. Figure shows maximum angle to one
flexible connections, the maximum turn
side and 50° to the other with minimal dis-
tance left for connections.
is 70° - for HEATER CONDENS MAX,
78° - for HEATER CONDENS CR1, CR2, CR3,
68° - for HEATER CONDENS ONE , to both
sides. Figure shows maximum angle to one
side and 50° to the other with minimal dis-
tance left for connections.
v202103
v202103
When
connecting
the
hydraulic
When
connecting
the
hydraulic
Advertisement
Table of Contents
